Transport; Cleaning And Maintenance - Scheppach DP50 Traduction Des Instructions D'origine

cross.
2. Loosen the quick clamping lever (17).
3. Place the quick clamp (2) on the workpiece.
4. Turn the quick clamp lever (17) clockwise to clamp
the workpiece.
5. Turn the quick clamp lever (17) counter-clockwise
to release the quick clamp (2).
10.7 Clamping larger workpieces (fig. 6)
Use the parallel stop (16) for larger workpieces:
1. Loosen the wing screws for the parallel stop (15)
and insert the parallel stop (16) into the grooves of
the base plate.
2. Tighten the wing screws for the parallel stop (15).
3. Align your workpiece against the parallel stop (16)
and clamp it with the quick clamp (2).
Warning! With workpieces that are wider or longer
than the tabletop, ensure that these are adequately
supported, e. g. through trestles or saw horses.
Workpieces that are longer or wider than the base
plate of the tabletop drill can tip if they are not prop-
erly supported. If the workpiece tips, this can damage
the chuck guard or the cutting tool.
10.8 Setting the drilling speed (fig. 1)
The correct speed must be set to suit the workpiece
to be drilled and the tool diameter.
Mechanical gear selection:
Two different speed ranges can be selected with the
gear selection switch (18).
Gear 1: Low speeds (170- 880 min
ameters.
Gear 2: High speeds (490-2600 min
diameters.
m Attention: Actuate the gear selector switch (18)
only when at a standstill. If the gear selection switch
(18) does not latch into place turn the chuck (14) a
little.
If the gear selection switch (18) cannot be turned as
far as the stop, turn the chuck a little with the drill.
Electronic speed control:
The speed of the individual gears can be seamlessly
adjusted with the electronic speed control:
Set the speed with the help of the speed control (12).
The current speed can be seen on the display (11).
24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
) for large tool di-
-1
) for small tool
-1
10.9 Displaying the drilling depth (fig. 1/5)
1. Set the display (11) to the "Drilling depth" indication
(button F).
2. Set the tip of the drill bit down lightly on the work-
piece.
3. Set the zero point by pressing the button (G).
4. Drill until the desired depth is shown on the display
(11).
10.10 Switching on/off (fig. 1)
m Make sure that the chuck guard (13) is folded
down before switching on.
Switching on: Press the on switch (10) to switch the
device on.
Switching off: Press the off switch (9) to switch the
device off.
10.11 Drilling procedure (fig. 1)
1. Align the workpiece and clamp it.
2. Start the device and set the speed.
3. Turn the handwheel (8) with uniform speed until
the desired drilling depth has been reached. When
drilling into metal, interrupt the downward pressure
briefly to break the swarf.
4. After reaching the drilling depth, turn the hand-
wheel (8) back to the starting position.
5. Switch the device off.

11. Transport

• To transport the device hold it by the base plate (1).

12. Cleaning and maintenance

m Warning! Pull out the mains plug before carrying
out any adjustments, maintenance or repair work!
General maintenance tasks
Wipe swarf and dust off the machine from time to
time with a cloth. Oil the rotating parts once monthly
to extend the life of the tool. Do not oil the motor.
Do not use corrosive agents for cleaning the plastic.
m Have tasks that are not described in this op-
erating manual, carried out by a specialist work-
shop. Use only original parts. Let the device cool
down before all maintenance and cleaning tasks.
m There is a risk of burn!
Before using the device each time, check the device
for obvious defects such as worn or damaged parts,
correct seating of screws or other parts. Replace
damaged parts.
Cleaning
Do not use cleaning agents or solvents. Chemical
substances could damage the plastic parts of the
device. Never clean the device under running water.
• Clean the device thoroughly after each use.
• Clean the ventilation holes and the surface of the
device with a soft brush or cloth.