Nail Selection; Standard Accessories; Optional Accessory; Applications - HIKOKI NV 100H Mode D'emploi

English

NAIL SELECTION

Wire collated nails can be driven with this tool.
Choose a suitable nail from Fig. Nails which are not shown
in Fig. can not be driven with this tool. Nails are linked and
rolled.
Wire-collatd coil nails
Min.
6 mm
(.236")
2.5 mm
(.099")
Dimensions of nails

STANDARD ACCESSORIES

(1) Eye protector ................................................................ 1
(2) Oiler .............................................................................. 1
(3) Nose cap ...................................................................... 1

OPTIONAL ACCESSORY

○ Single Sequential Actuation Mechanism Kit
(Sequential Fire Parts Set, Single Shot Parts)
With the sequential fi re parts,the nail is driven only
by squeezing the trigger after pushing down the push
lever.
By installing these parts, driving nails into improper
positions and unexpected fi ring of nails caused
by accidental operation of the push lever can be
prevented.

APPLICATIONS

○ Construction wooden works such as fl oor and wall
framing, roof decking and subfl ooring.
○ Mobile and modular home construction.
○ Making wooden boxes, palletes, and drums.
○ Packing operations in manufacturing plants, and other
types of packing and crating work in general.
PREPARATION PRIOR TO OPERATION
1. Prepare the hose
Use an air hose designed for high-pressure operation.
Be sure to use the hose provided with minimum 5 mm
(13/64") inside diameter.
NOTE
The air supply hoses must have a minimum working
pressure rating of 29.4 bar (420 psi).
2. Check on safety
CAUTION
○ Unauthorized persons (including children) must be kept
away from the equipment.
10
○ Wear eye protector.
○ Check the retaining screws which fi x the exhaust cover,
○ Check whether or not the push lever works correctly.
○ Recheck on operational safety.
Max.
BEFORE USE
7.9 mm
(.311")
1. Check the air pressure
CAUTION
3.8 mm
2. Lock mechanism of the trigger
(.148")
CAUTION
3. Lubrication
(1) Be sure to lubricate this nailer at least twice a day. To
(2) It is recommended using the recommended oil (SHELL
4. Load Nails
(1) Grip the nail guide and knob with fi nger.
(2) Adjust the position of the nail holder according to the
(3) Place the nail coil into the magazine.
(4) Close the magazine cover fi rst and swing the nail guide
(5) Lock the knob correctly.
etc. for tightness.
Check the nailer for air leaks and defective or rusty
parts.
Also check whether or not any dirt has adhered to the
moving parts of the push lever.
Use a compressor designed for high-pressure
operation.
The air pressure must be constantly maintained at
12 – 23 bar (170 – 320 psi).
Adjust the air pressure between 12 to 23 bar (170 –
320 psi) according to the diameters and length of nails
and hardness of the wood being nailed. Pay special
attention to the output pressure, capacity, and piping
on the air compressor, so that air pressure does not
exceed the specifi ed limit. Note that excessive pressure
may aff ect overall performance, service life, and safety.
This device has a lock mechanism to prevent the trigger
from pulling.
Set the lock lever to "Lock" position to lock the trigger in
place.
To drive a nail, turn the lock lever to the "Free" position.
When not driving nails set the lever to the "Lock"
position (Fig. 2).
Keep the trigger locked at all times except when driving
nails.
lubricate, pour 10 to 15 drops of oil into the air plug
before and after using this nailer. The oil applied before
use lubricates this nailer; the oil applied after use
prevents rust.
TONNA). Other applicable oils are listed. Never mix two
or more types of diff erent oils.
Press the knob down and swing the nail guide open.
And open the magazine cover (Fig. 3).
nail length (Fig. 4).
The nail will not feed smoothly if the nail holder is not
correctly adjusted (Fig. 5).
a. Turn the nail holder
counterclockwise.
b. Slide in vertical direction possible.
Lift or lower the nail holder to accept diff erent length
nails.
c. Adjust the plate to the nail length reference points
on the magazine cover and turn the nail holder 90
degrees clockwise until you hear "click".
Uncoil enough nails to reach the driving hole (Fig. 6).
Insert the fi rst nail into the driving hole and the second
nail between the two pawls of the feeder.
Fit the nail head in the guide slot (Fig. 7).
closed (Fig. 8).
about 90 degrees