Intended Use; Other Risks - Scheppach Structo 5.0 Traduction Du Manuel D'origine

• Do not use defective lines. See "Electrical connec-
tion".
• Please be vigilant the machine is steadfast.
• Please pay attention that the construction circular saw
is steadfast while being assembled.
• Keep children away from the to power supply connected
machine.
• The minimum age for the operating person is 18
years.
• People running the machine should not be distracted.
• Keep the operating site free from wood chips and
waste.
• Pay attention to the rolling direction of the motor and
saw blade. See instructions "Electrical connection"
page U5 (wall mounted connector).
• Build in only well sharpened, slit free and non-de-
formed saw blades.
• Circular saw blades made out of high-performance steel
should not be built in.
• The security facilities of the machine should not be
dismantled nor be made unusable.
• The slit wedge is an important security facility, which
leads the workpiece and avoids the closing of the joints
behind the saw blade and the reversing of the work-
piece. Please note the thickness of the slit wedge –
see the staved in nºs on the slit wedge. The slit wedge
should not be thinner than the saw blade and not thick-
er than its intersection width.
• Put the cover on the workpiece at every operation.
• The cover should be put horizontal above the saw blade
at every operation.
• When cutting lengthwise small workpieces – less than
120 mm – implicitly use the spline end.
• To repair disorders or to pull out jammed pieces of
wood, switch the machine off. Pull out power plug!
• In case of a knocked-out sawing split, renew the inset.
Pull out power plug!
• Modifying as well as adjusting, measuring and clean-
ing to be carried out only when motor is switched off.
Pull out power plug!
• Upon leaving the working place, switch off the motor.
Pull out power plug!
• Installations, repairs and maintenance with regards to
the electrical instalIation should only be carried out
by specialists.
• The machine is only intended for industrial use.
• Wear protection gloves when exchanging the saw
blade.
• All protection - and safety instructions must be as-
sembled imediately after finished repair and mainte-
nance works.
• Also upon the slightest position movement separate the
machine from the external power supply! Upon return
to service, connect the machine to the power supply
according to the rules!
m Intended use
The machine complies with the valid EG Machines guide-
line.
• The Scheppach construction circular saw should not be
used in closed rooms.
• Only work with ear protection.
• The machine is built according to the electronic level
and the safety-related rules. Nevertheless, danger for
life and limb of the user or a third party, respectively
damage to the machine and other intrinsic values can
10 english
arise during its use.
• Use the machine only in technical impeccable condi-
tion as well as according to its intended use, and in a
safety and danger conscious manner with observance of
the operational constructions! Immediately eliminate,
or have eliminated, in particular those disorders that
can harm the safety!
• The Scheppach construction circular saw has been con-
structed exclusively with tools supplied by Scheppach,
according to EN 847-1 and accessories constructed for
the sawing of wood. Please note that while sawing all
workpieces should be held and led safely.
• The maximum workpiece thickness is 125 mm for the
Structo 5.0 WE and 150 mm for the Structo 5.0 DR.
• Every use surpassing this counts as non-intended use.
In this case the manufacturer is not liable for dam-
ages caused; therefore the user only bears the conse-
quences.
• The safety, work and maintenance regulations of the
producer as well as the measurments mentioned in the
"Technical information" must be adhered to.
• Attention must be paid to the applicable prevention of
accidents rules and to the other, generally accepted
safety-related rules.
• The Scheppach construction circular saw should only
be used, maintained or repaired by people who are fa-
miliar with it and informed about the risks. Arbitrary
changes to the machine exclude liability of the manu-
facturar.
• The Scheppach construction circular saw should only
be used with original accessories, original extension
tools and original saw blades of the manufacturer.
• According to the currently valid regulations the use
of this machine is not allowed in closed rooms. The
machine should only be used outside or in sufficiently
ventilated rooms.
m Other risks
• The machine is built according to the up to date tech-
nical level and the accepted safety-related rules. How-
ever, some remaining risks might appear during work.
• Risk of injury to fingers and hands by the rotating saw
blade in case of incorrect usage of the workpiece.
• Injuries because of the workpiece being slung away
due to incorrect holding or usage, such as working with-
out end stop.
• Risk to health because of wood dust or wood splinters.
Wear personal protection gear such as eye protection
and dusk mask without fail.
• Injuries caused by a defect saw blade. Check the saw
blade regularly for its integrity.
• Electricity danger, in case electrical connections that
are not according to the rules are used.
• Furthermore, despite of all precautions unapparent re-
maining risk can exist.
• Remaining risks can be minimized, when the "Safety
information" and the "Intended use" as well as the op-
erational instructions are both respected.
• Deactivate the machine and pull out the power plugs
when you want to clean the machine.
• Keep the electrical connections always oil and grease
free.
• The machine has a working area that is in front of the
machine.
• For cleaning always switch off the machine and pull
the power plug.