General Instructions; Safety Instructions - Scheppach Structo 5.0 Traduction Du Manuel D'origine

Manufacturer:
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear client,
We hope you will enjoy your new Scheppach construction
circular saw and wish you success with it.
The manufacturer of this tool is, according to the current
product liability law, not liable for damages caused to or
by this tool because of:
• incorrect usage,
• failure to observe the manual,
• repairs by third parties, not authorized specialists,
• fitting and exchange of non-original exchange parts,
• non-intended use,
• failure of the electrical installations because of inob-
servance of the electrical Rules and VDE-Regulations
0100, DIN 57113/VDE0113.
We recommend that you:
Read the entire operating instructions before assembling and
implementing.
This instruction manual should make it easier for you
to get to know your machine and to use its range of ap-
plications as intended. The manual contains important
information on how to work with the machine in a secure,
correct and efficient way, and how you can avoid risks,
save repair costs, reduce down time and increase the
reliability and life span of the machine. Apart from the
security rules mentioned in these operating instructions,
you should implicitly pay attention to the valid regula-
tions of your country for the use of the machine. Keep
the manual, in a plastic cover protected against dirt and
humidity, with the machine. They should be read and
observed carefully by every member of staff before start-
ing to work. Only people instructed on how to use the
machine and informed about the possible risks, should
be allowed to use it. The required minimum age is to be
adhered to. Besides the safety instructions in this manual
and the special regulations of your country the recognized
technical rules for the operation of wood processing ma-
chines need to be observed.

General instructions

• After unpacking please check all parts for possible
damage during transport. In case of complaints the
driver needs to be contacted as soon as possible.
• Complaints coming in later will not be recognized as
such.
• Check if the consignment is complete.
• Familiarize yourself with the machine by means of the
operating instructions before implementing it.
• In case of replacing worn or exchange parts, as for ac-
cessories, only use original Scheppach parts. You can
obtain exchange parts at the specialized dealer.
• Upon ordering, please specify our article nºs as well as
type and year of construction of the tool.
Structo 5.0 - WE
Scope of delivery
Construction circular
saw
Longitudinal end
stop
Crosscut gauge
Saw blade
Spline end
Push stick
Blade wrench
Rest key
Assembly
accessories
Manual
Technical information
Measurements
1075 x 790 x 1035 1075 x 790 x 1035
LxWxH mm
Table size mm 660 x 1000
450
Saw blade ø mm
Cut height mm. 125
Rotation nº
2800
1/min.
Weight kg 103
Power unit
Motor 230 V/50 Hz
Aufnahmeleistung
3,6
P1 kW
Abgabeleistung
2,6
P2 kW
Subject to technical changes!
Noise specific values
The according to the EN 23746 for the sound pressure
level resp. EN 31202 (correction factor k3 after sup-
plement A.2 from EN 31204 calculated) for the sound
pressure level on the working site ascertained noise emis-
sion value amounts under the foundations of ISO 7960
supplement A performed working conditions to:
Sound pressure level in dB
Idle state L = 103 dB(A),
WA
Processing L = 108 dB(A)
WA
There is a measurement insecurity allowance K=4dB for
the mentionned emission values.
In these operating instructions we have indicated positions
that concern your safety with this mark: m
m Safety instructions
• Forward the safety instructions to all people working on
or with this machine.
• The machine is only to be used in technically faultless
condition as well as according to its intended use, and
in a safety and risk conscious manner, and with ob-
servance of the operation instructions! Especially mal-
functions that can threaten safety have to be repaired
immediately.
• Pay attention to all safety and risk instructions of the
machine.
• Keep all safety and risk instructions of the machine
completely readable.
• The circular saw should not be used to saw firewood.
• Be careful at work: Danger of damaging finger(s) and
hand(s) by the rotating cutting tool.
• Check power supply lines.
Structo 5.0 - DR
Construction circular
saw
Longitudinal end
stop
Crosscut gauge
Saw blade
Spline end
Push stick
Blade wrench
Rest key
Assembly
accessories
Manual
660 x 1000
500
150
2800
103
400 V/50 Hz
4,2
3,3
english 9