Lenze E82MV Série Instructions De Montage page 109

Code Possible settings
No. Name Lenze
C0007
v
uSEr
(Contin.)
C0007
v
uSEr
(Contin.)
C0010 Minimum 0.00
output
uSEr
frequency
C0011 Maximum 50.00 7.50
output
uSEr
frequency
C0012 Acceleration 5.00
time main
uSEr
setpoint
C0013 Deceleration 5.00
time main
uSEr
setpoint
EDK82MV752 DE/EN/FR 7.2
Selection
E4 E3
DCB QSP
31
32 TRIP−Set QSP
33 QSP PAR
34 CW/QSP CCW/QSP
35 JOG2/3 JOG1/3
36 DCB QSP
37 JOG1/3 QSP
38 JOG1/3 PAR
39 JOG2/3 JOG1/3
40 JOG1/3 QSP
E4 E3
JOG1/3 DCB
41
QSP DCB
42
43 CW/CCW QSP
44 UP DOWN
45 CW/CCW QSP
46 H/Re PAR
47 CW/QSP CCW/QSP
48 DCB
PCTRL1−OFF
49 JOG1/3
PCTRL1−OFF
50 JOG1/3
PCTRL1−OFF
51 DCB PAR
255 Free configuration in C0410
0.00 {0.02 Hz}
à 14.5 Hz
{0.02 Hz}
à
87 Hz
0.00 {0.02 s}
0.00 {0.02 s}
l
Commissioning
Important controller codes
IMPORTANT
E2 E1
DFIN1−ON
PCTRL1−I−OFF
DFIN1−ON
PCTRL1−I−OFF
DFIN1−ON
PCTRL1−OFF
DFIN1−ON
PCTRL1−I−OFF
PAR DFIN1−ON
PAR DFIN1−ON
PAR DFIN1−ON
TRIP−Set DFIN1−ON
TRIP−Set DFIN1−ON
TRIP−Set DFIN1−ON
E2 E1
TRIP−Set DFIN1−ON
TRIP−Set DFIN1−ON
TRIP−Set DFIN1−ON
PAR DFIN1−ON
PAR DFIN1−ON
QSP JOG1/3
H/Re JOG1/3
DFIN1−ON
PCTRL1−I−OFF
QSP DFIN1−ON
DFIN1−ON
PCTRL1−I−OFF
DFIN1−ON
PCTRL1−I−OFF
Read only
Do not change C0007 since settings
in C0410 may get lost
l C0010 not effective in the case of
650.00
bipolar setpoint selection (−10 V ...
+ 10 V)
l
C0010 only limits the analog input
1
l In the case of a max. output
frequency > 50 Hz the switching
threshold of the auto DCB in
C0019 has to be increased.
650.00
l
From software 3.5: If
C0010 > C0011, the drive does not
start when controller enable is set.
à Speed setting range 1 : 6 for Lenze
geared motors: For operation with
Lenze geared motors has to be set
necessarily.
1300.00 Reference: frequency change 0 Hz ...
C0011
Additional setpoint ðC0220
l
l
Acceleration times that can be
activated via digital signals ð
C0101
1300.00 Reference: frequency change C0011...
0 Hz
Additional setpoint ðC0221
l
l
Deceleration times that can be
activated via digital signals ð
C0103
6
109