Getting To Know Your Grill; Control Board - Pit Boss Pb1300Ps4 Manuel D'instructions

GETTING TO KNOW YOUR GRILL

F
E
D
C
B
A
H Grill Probe (Sensor)
A Access Panel
Remove the access panel to gain access to the electrical
components for repair and maintenance.
B Control Board
The control system that manages the feed rate of pel-
let fuel, the fan speed, and environment settings.
I
C Hopper
A bigger hopper to last a full smoking session. The hop-
per safety screen breaks apart any clumps of fuel when
added. The outlets on the back can power an appliance
J
less than 5A (left), and power the unit (right).
D Hopper Handle
Use this inset handle on the hopper to tilt and move
the grill from one area to another.
K Removable Burn Pot
E Hopper Sight Glass
Easily observe the level of pellets in your hopper with-
out constantly opening the hopper lid.
F Flame Broiler™ Adjustment Bar
Adjust the flame broiler slide plate safely and easily by
L
moving the bar left or right.
G Front and Side Shelves
Convenient shelves add ample space for food prep.
The side shelf is equipped with tool hooks and a bottle
opener.
PIT BOSS® GRILLS
H I
G
K
iii
ii
i
This vertical piece of stainless steel measures the
internal temperature of the unit. Set the temperature
on the control board, then the grill probe will read the
internal temperature the unit and adjust to the desired
target temperature.
COOKING
Flame Broiler™ Main Plate
AREA
Sear and flame broil to your liking with direct flame
over the burn pot. Brand dark lines into meat like your
3,609 CM² /
i
favorite steakhouse.
559.4 IN²
Flame Broiler™ Slide Plate
2,711 CM² /
Indirect heat, or convection cooking, is possible when
ii
the slide plate covers the slits of the main plate. Infuse
420.3 IN²
more flavor into large cuts of meat or delicate foods
with indirect heat.
2,063 CM² /
iii
319.7 IN²
Open the cart cabinet to gain access. Easily release the
buckle latch to remove the burn pot, empty ashes, and
8,383 CM² /
return into position. Keep the buckle latch secure to iv
1,299.4 IN²
avoid heat loss while in use.
Grease Bucket
Open the cart cabinet to gain access to the grease
bucket. It captures the cooking grease from the grill
to keep a clean, cooking area. Easily remove from the
undercarriage spout to empty.
6 WWW.PITBOSS-GRILLS.COM
A B
J
C D
L
A Power Button
Press and hold for three seconds to turn on, activating
the Start Screen for selection of cooking mode. Press
and hold for three seconds to turn off, activating the
iv
cool-down cycle. The button will glow blue if unit is
connected to a power source.
B Display Screen
The touch screen is both the information center and
a menu to choose your selections. The screen is very
sensitive and requires only a light touch to activate and
control. During use, the display screen will show menus
and the appropriate selections for the options being
chosen. This Start Screen will show by default once the
power to the unit is turned on. The display screen will
go into screen saver mode if inactive for 5 minutes.
C Controller Knob
Navigate, increase or decrease, make selections, and set
values. Rotate the wheel to scroll through sub-screen
options. Push the Controller Knob to activate a change
to the Target grill tempereature. A selection will blink
blue when selected for adjustment. Push the Controller
Knob to confirm/accept the chosen value or selection,
turning it white.
D Meat Probe Connection Ports
Plug-in the adapter end of a meat probe to either
of the connection ports. The readout will appear on
the display screen for the corresponding meat probe
selected. The left probe port is P1 and the right probe
port is P2.
E Target Temperature
Displays the desired target temperature. This is the
temperature that is selected by using the Controller
Knob.
F Actual Temperature
Displays the Actual temperature from inside the main
barrel. Readout is taken by the grill probe (sensor).
WWW.PITBOSS-GRILLS.COM

CONTROL BOARD

G H
F
E
G Operation Icons
An icon is visible when a component is in operation.
Should a malfunction occur with a component, an error
screen will be displayed. See Troubleshooting for assis-
tance. Run a diagnostics test upon restarting the unit.
H Connectivity Icon
Indicates a connectivity with Wi-Fi. When searching for
connection, the icon will blink. Once the connection is
made, the icon will stay solid.
common FAQs online
I Settings
This menu allows access to customizing functions and
data for your grill. These settings allow you access the
P Setting, adjust the display screen brightness, switch
the temperature scale, set the screen saver, adjust the
start-up temperature, change the language, and more.
J Menu
This menu gives access to the Prime function. Selecting
this menu will give users the option to dispense a
continuous feed of pellets into your grill, or feed pellets
for a preset length of time.
K Meat Probe Readouts
These two readouts will display the temperature read-
ings of the programmable meat probe(s) connected:
the large value is the Actual temperature, small value is
the Target temperature. The readout corresponds with
the plug-in connection port selected.
7
I
J
K
HAVE A
QUESTION?
Check out some
or Live Chat with
Customer Care.
PIT BOSS® GRILLS