ABB High dynamic performance HDP Serie Manuel D'installation, D'utilisation Et De Maintenance page 30

ENGLISH
NDE 6316
h250 DE 6322
NDE 6319
h280 DE 6322
NDE 6316
h315 DE 6326
NDE 6322
h355 DE 6326
NDE 6322
h400 DE 6330
NDE 6326
WARNING:
1.7.2.4 Lubricants
WARNING:
When regreasing, use only special ball bearing grease with the following properties:
• Good quality grease with lithium complex soap and with mineral- or PAO-oil
• Base oil viscosity 100-160 cST at 40°C
• Consistency NLGI grade 1.5 - 3 *)
• Temperature range –30°C - +120°C, continuously
*) A stiffer end of scale is recommended for vertical mounted motors or in hot conditions.
The above mentioned grease specification is valid if the ambient temperature is above –30°C or below +55°C, and the
bearing temperature is below 110°C; otherwise, consult ABB regarding suitable grease.
Grease with the correct properties is available from all major lubricant manufacturers.
Admixtures are recommended, but a written guarantee must be obtained from the lubricant manufacturer, especially
concerning EP admixtures, that admixtures do not damage the bearings or the properties of lubricants at the
operating temperature range.
The following high performance greases can be used:
Mobil Unirex N2 orN3 (lithium complex base)
•
• Mobil Mobilith SHC 100 (lithiumcomplex base)
• Shell Gadus S5 V 100 2 (lithiumcomplex base)
Klüber Klüberplex BEM 41-132 (special lithium base)
•
• FAG Arcanol TEMP110 (lithiumcomplex base)
Lubcon Turmogrease L 802 EP PLUS (speciallithium base)
•
• Total Multis Complex S2 A (lithium complex base)
NOTE:
The following greases can be used for high speed motors but not mixed with lithium complex greases:
Klüber Klüber Quiet BQH 72-102 (polyureabase)
•
• Lubcon Turmogrease PU703 (polyureabase)
If other lubricants are used, check with the manufacturer that the qualities correspond to those of the above
mentioned lubricants. The lubrication intervals are based on the listed high performance greases above. Using other
greases can reduce the interval.
Motors in the range 80-180 have permanently lubricated bearings, these data are applicable to, e.g., VC 037, 041, 640.
Motor Speed [RPM]
35 N/A
60 16900
45 19100
60 16900
35 21100
85 14800
60 16900
85 14800
60 16900
105 13000
85 14800
The maximum operating temperature of the grease and bearings, +110°C, must not
be exceeded. The designed maximum speed of the motor must not be exceeded.
DO NOT MIX DIFFERENT TYPES OF GREASE! INCOMPATIBLE LUBRICANTS MAY
CAUSE DAMAGE TO THE BEARINGS.
Always use high speed grease for high-speed motors where the speed factor is
higher than 480,000 (calculated as Dm x n where Dm = average bearing diameter,
mm; n = rotational speed, r/min)!
13800 9600 N/A
9600 5600 4200
11700 7600 6100
9600 5600 4200
13800 9600 8000
7600 3900 2700
9600 5600 4200
7600 3900 2700
9600 5600 4200
6000 2600 1600
7600 3900 2700
30
6700 N/A
3100 N/A
4900 N/A
3100 N/A
6700 N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A