Cleaning And Maintenance; Storage And Transport; Electrical Connection - Scheppach dp13 Traduction Du Manuel D'origine

9. Cleaning and maintenance

WARNING:
For your own safety, turn the switch off and remove
plug from power source outlet before any operation
of maintenance on our drill press.
Keep your appliance clean.
Be careful some household cleaning products and
solvents such as benzine, trichloroethene, chloride,
ammonium, etc., can damage plastic parts.
To avoid motor darnage, blow out or vacuurn fre-
quently this motor to keep drill press dust from inter-
fering with normal motor ventilation.
Power cord.
To avoid shock or fire hazard, if the power cord is
worm or cut, or damaged in any way, have it replace
immediately.
Lubrication.
All of the ball bearings are packed with grease at the
factory. No further lubrication is required.
Periodically lubricate the splines -grooves -in the
spindle.
To lubricate the splines, bring do the quill and ject
the grease into the spindle from the top of the pulley.
Bring the quill up and down a few times.
Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brushes, v-belt, drill
* Not necessarily included in the scope of delivery!
10. Storage/Transport
Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing tem-
perature. The ideal storage temperature is between 5
and 30 °C. Store the electric tool in its original pack-
aging.
m Attention! Unplug the machine!
The appliance must unconditionally be secured
against falling or turning down during transport.
The appliance can be lifted on the left and right grind-
ing wheel / belt sander cover. Power cable, flexible
lamp shaft etc. should not be used for transport pur-
pose.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

11. Electrical connection

The installed electric motor is completely wired ready
tor operation. The customer's connection to the pow-
er supply system, and any extension cables that may
be used, must conform with local regulations.
Defective electrical connection cables
Electrical connection cables offen suffer insulation
darnage.
Possible causes are:
• Punch points when connection cables are run
through window or door gaps.
• Kinks resulting from incorrect attachment or laying
of the connection cable.
• Cuts resulting from running over the connecting
cable.
• Insulation darnage resulting from forcefully pulling
out of the wall socket.
• Cracks through aging of insulation.
Such defective electrical connection cables
must not be used as the insulation darnage
makes them extremely hazardous.
Check electrical connection cables regularly for dar-
nage. Make sure the cable is disconnected from the
mains when checking.
Electrical connection cables must comply with the
regulations applicable in your country .
Single-phase motor
• The mains voltage must coincide with the voltage
specified on the motor.s rating plate.
• Dimension cables up to a length of 25 m must have
a cross-section of 1.5 mm
least 2.5 mmª.
• The connection to the mains must be protected
with a 16 A slowacting fuse.
Important remark:
The motor is automatical/y switched off in the event
of an overload. The motor can be switched on again
after a cooling down period that can vary.
Three-phase motor
• The mains voltage must be between 380 and 420
V / 50 Hz.
• The connection to the mains and the connection
cable must have five leads (3 P + N + PE).
• Extension cables must have a cross-section of at
least 1.5 mm .
2
Warning:
The drill press must not be operated in the open air.
The machine must have an earth Gable to protect
the operator from etectrical shocks.
GB
. and beyond 25 m at
2
25 / 152