Cleaning And Maintenance - Scheppach dp13 Traduction Du Manuel D'origine

GB
6 Tighten belt tension lock knob. Belt should deflect
approximately 13 mm –1/2" -by thumb pressure at
mid-point of belt between pulleys.
7 Close pulley cover .
8 If belt slips while drilling readjust belt tension.
Tip: Safety switch
If you want to adjust speed you have to open the pulley
cover. The device switches off immediately to avoid the
risk of injuries.
Removing the chuck
Open jaws of chuck as wide as they go by turning chuck
sleeve anticlockwise (when viewed from above).
Carefully tap chuck with mallet in one hand while holding
chuck in other hand to prevent dropping it when released
from spindle nose.
Depth stop, Fig. 14
The depth stop enables the drilling of holes in the work-
piece until a defined depth. You have two options for that.
Drilling to a specific depth.
1 Mark the drilling depth (H) on one side of the work-
piece.
2 WITH THE SWITCH „OFF", bring the drill bit down until
the tip or lips are even th the mark.
3 Hold the feed handle at this position.
4 Spin the lower nut (B2) down to contact the depth stop
lug (13) on the head.
5 Spin the upper nut (B1) down and tighten against the
lower nut.
6 The chuck and the drill bit wiII now be stopped after
traveling downward the distance selected on the depth
scale.
Depth scale method, Fig. 6
Note: for this method, with the spindle in its upper posi-
tion the tip of the drill bit must be just slightly above the
top of the workpiece.
1 Switch off the machine, lower the drill so far until the
indicator (g) points at the desired drilling depth of the
depth scale (e).
2 Turn the lower nut (B2) downwards until it reaches
the lower stop (13).
3 Lock the lower nut (B1) against the upper nut.
4 The chuck and the drill bit will now be stopped af-
ter traveling downward the distance selected on the
depth scale.
Positioning table and workpiece, Fig. 15
Always place a piece of back up material (H) ('wood, ply-
wooood...) on the table undemeath the workpiece (B).
This wiII prevent splitering or making a heavy burr on
the underside of the workpieces as the drill bit breaks
through. To keep the back up material from spinning out
of control it must contact the left side of the column as
illustrated.
24 / 132
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Warning:
to prevent the work piece or the backup material from
being torn from your hand whiile drilling, position them
to the left side of the column. If the work piece or the
backup material are not long enough to reach the col-
umn, clamp them to the table. Failure to do this could
result in personal injury.
Note: for small pieces that cannot be clamped to the ta-
ble, use a drill press vise (Optional accessory).
The vice must be clamp or bolt to the table to avoid injury
from spinning work and vise or tool breakage.
Drilling a hole.
Make a dent in the workpiece where you want the hole,
using a center punch or a sharp nail. Before turning the
switch on, bring the drill down to the workpiece lining it
up with the hole location.
Turn the switch on and pull down on the feed handles
with onIy enough effort to allow the drill to cut.
FEEDING TOO SLOWLY might cause the drill bit to
burn.
FEEDING TOO RAPIDLY might stop the motor, cause
the bett or drill to slip, tear the workpiece loose, or break
the drill bit.
When drilling metal, it may be necessary to lubricate the tip
of the drill with motor oil to prevent burning the drill bit.

9. Cleaning and maintenance

WARNING:
For your own safety, turn the switch off and remove plug
from power source outlet before any operation of mainte-
nance on our drill press.
Keep your appliance clean.
Be careful some household cleaning products and sol-
vents such as benzine, trichloroethene, chloride, ammo-
nium, etc., can damage plastic parts.
To avoid motor darnage, blow out or vacuurn frequently
this motor to keep drill press dust from interfering with
normal motor ventilation.
Power cord.
To avoid shock or fire hazard, if the power cord is worm
or cut, or damaged in any way, have it replace immedi-
ately.
Lubrication.
All of the ball bearings are packed with grease at the fac-
tory. No further lubrication is required.
Periodically lubricate the splines -grooves -in the spindle.
To lubricate the splines, bring do the quill and ject the
grease into the spindle from the top of the pulley. Bring
the quill up and down a few times.
Maintenance
There are no parts inside the equipment which require
additional maintenance.