Scheppach dp13 Traduction Du Manuel D'origine page 21

General safety regulations and accident prevention
It is essential that you read the safety regulations and
operating instructions in their entirety and follow the
information contained therein in order to eliminate the
possibility of an accident or potentially dangerous situa-
tion from occurring while working with the machine.
• Always check the device, the mains cable and the
plug before using the device. Only operate the
tool when it is in good working order and is not
damaged in any way. Damaged parts have to be
replaced immediately by a qualified electrician.
• Always pull the power plug out of the socket outlet
before doing any work on the machine, before
changing tools and whenever the machine is not
being used.
• To prevent damage to the power cable, always
lead the power cable away from the rear of the
machine.
• Keep the tools in a safe place and out of the reach
of children.
Special safety instructions
1. The pillar drill was designed in such a way so as
to all but eliminate potential hazards when the ma-
chine is properly used. However, there are a few
safety precautions to observe in order to ensure
that all residual hazards are ruled out.
2. Ensure proper voltage
The voltage must comply with the specifications on
the rating plate.
3. Use a socket-outlet with earthing contact
The device may only be operated from an outlet
with the properly installed earthing contact.
4. Extension cable
The cord cross section of an extension cable must
measure at least 1.5 mm2. Always completely un-
wind a cable reel prior to use. Check the cable for
defects.
5. Protection against electrical shock
Keep the device away from moisture. The device
must neither be damp nor be operated in a humid
environment. Prior to every use, check the device
and the mains cable with plug for damage. Avoid
bodily contact with earthed parts e.g. pipes, hot ele-
ments, etc.
6. Protection against fire and explosion
There are spark producing components inside the
device. Do not use the device in the vicinity of com-
bustible liquids or gases. Otherwise there is a risk
of fire or explosion.
7. Handle the device with care
Do not use the cable to pull the plug out of the sock-
et. Protect the cable from heat, oil and sharp edges.
Keep your tools sharp and clean so that you can
work efficiently and safely. Follow the maintenance
regulations and the instructions for changing tools.
8. Wear suitable work clothes and personal protection
equipment
Loose clothing is not suitable, as it can be caught
by moving parts, causing you to become entangled.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Wear a hair net if you have long hair. As a general
rule, jewelry should not be worn when working with
machine tools. Ensure that you wear safety gog-
gles. Not doing so could result in eye injury.
9. Keep your work area neat and tidy
Disorder in the work area can easily lead to acci-
dents. Do not leave any tools, objects, or cable in
the direct vicinity of the work area, as this poses a
tripping hazard! Ensure that there is sufficient light-
ing.
10. Watch out for other persons
Watch out for other persons (especially children)
when using the device, and keep them away from
your work area. Do not let anyone touch the device
or the power cable.
11. Store the tools in a safe location
Store unused devices in a dry, locked location that
is out of the reach of children.
12. Avoid overloading the device
Operate the device only within the specified output
range. Do not use any low-powered machines for
heavy duty work. Do not use tools to perform work
for which they were not intended.
13. Maintain a steady foothold
Ensure that you maintain a steady foothold while
working. Avoid abnormal body positions and always
keep your balance.
14. Pull out the mains plug
Pull out the mains plug when not using the tool, prior
to maintenance, and when changing the drill bit.
15. Pull out the power plug.
Ensure that the mains connection is protected by at
least a 10 A-rated fuse.
16. Avoid unintentional start-up
Ensure that switch is turned off when plugging the
plug into the socket.
17. Keep an eye on your work
Always keep an eye on your machine and the object
you are working on. Never use the machine when
you are not concentrating or are distracted. Never
use the machine when you are under the influence
of alcohol or are taking medication.
18. Check the tool for damage
Before using the tool, safety devices and any slight-
ly damaged parts must be carefully checked to en-
sure that they are in good working order. Visually
examine the tool's power cable on a regular basis.
All parts must be correctly assembled and meet all
the conditions required to ensure proper operation.
19. Unless otherwise specified in the operating instruc-
tions, any damaged safety devices and parts must
be properly repaired or replaced by a professionally
recognized workshop. Never use tools with defec-
tive On/Off switches.
20. Warning! Using any plug-in tools and accessories
other than those specified in these operating in-
structions can lead to injury.
21. Maximum workpiece size
Workpieces (max. 20 x 20 cm) may only be pro-
cessed if they can be clamped securely on the drill
table or in the vise.
GB
21 / 132