Load Management (Optional); Operating Home Eco; Charging A Vehicle; Home Eco Diagnostics - AMPERFIED Wallbox Energy Control Manuel D'utilisation

Six white flashes, pause, three blue flashes (10% on,
90% off), pause (Fig. XVI-A no. 6)
Communication with the vehicle disrupted or maxi-
mum set current exceeded.
Check whether the charging cable is plugged
•
into the vehicle correctly.
After a self-test has been performed and the fault
has been corrected, the front illumination lights up
white. The vehicle can request the charging process.
Six white flashes, pause, six rapid blue flashes,
pause (Fig. XVI-A no. 7)
Internal fault in the Wallbox.
Unplug the charging cable from the vehicle.
•
Disconnect the Wallbox from the power supply
•
by switching off the respective circuit breakers
in the building. Wait approx. 1 minute and then
switch the circuit breaker back on.
Re-connect the charging cable to the vehicle.
•
After a self-test has been performed and the fault
has been corrected, the front illumination lights up
white. The vehicle can request the charging process.
Troubleshooting
If one of the faults listed persists, please contact our
Customer Support team.
Load management (optional)
2.2.3.
The Wallbox Energy Control can be operated with
a load management system. This enables the
Wallbox to operate in various modes such as:
Operation of several Wallboxes in an integrated
•
network with monitored power distribution (load
management),
Operation of the Wallbox with different energy
•
sources such as solar energy or the normal elec-
trical mains.
More information is available on-line, in the instruc-
tions "Wallbox Energy Control, Local Load Manage-
ment and External Load Management":
www.amperfied.com
Operating Home Eco
2.3
Charging a vehicle
2.3.1.
1. Fully unwind the charging cable from the Wallbox.
2. Remove the cover cap from the charging cable
coupler.
3. Plug the charging cable into the vehicle.
As soon as you have plugged the charging cable
into the vehicle, the Wallbox switches to "ready
for operation" and the LED lights up green. After
approx. 12 minutes in the ready for operation state
without a connected vehicle, the Wallbox enters
standby state and the LED goes out (Fig. XIV-B).
Wake-up option 1:
When the charging cable is connected to the
•
vehicle in the standby state, the Wallbox will auto-
matically switch to the ready for operation state.
The LED lights up green.
Wake-up option 2:
Pressing the pushbutton (without connected
•
vehicle) will cause the Wallbox to switch from the
standby state to the ready for operation state. The
LED lights up green, and the charging cable can
be connected to the vehicle.
If an external blocking device is used,
i
the system checks whether an external
block (due to a key-operated switch, for
example) is active when the vehicle is
connected. The LED lights up yellow and
charging does not take place until exter-
nal enabling has been issued. The LED
lights up green when external enabling
has been issued.
Charging process
The vehicle can start the charging process as soon
as you have inserted the charging cable. The LED
flashes green during the charging process. When
the vehicle ends the charging process, the Wallbox
completes the charging process. The LED lights up
green. These two operating states can repeat several
times during a complete charging cycle.
End of charging
When the charging process has ended, unplug the
charging cable from the vehicle and close the charg-
ing cable coupler with the cover cap. Then wind the
charging cable onto the Wallbox.
The charging cable could pose a tripping
i
hazard if is not wound up and is lying
loosely on the ground. Be sure not to pull
on the cable with too much force or wind
it too tightly. The cable can break if it is
repeatedly pulled with too much force
or wrapped too tightly.
Interrupting charging
The charging process cannot be cancelled using the
pushbutton (Fig. XVI-B no. 1). There are three options
for stopping the charging process:
End the charging process using the vehicle's
•
control elements. Refer to the vehicle's driver's
manual for this purpose.
Disconnect the Wallbox from the power supply
•
by switching off the building's circuit breakers.
English
31