Scheppach HMS1070 Traduction Des Instructions D'origine page 26

11 Do not abuse the cord
- Never yank the cord to disconnect it from
the socket. Keep the cord away from heat,
oil and sharp edges.
12 Secure work
- Where possible use clamps or a vice to hold
the work.
lt is safer than using your hand.
13 Do not overreach
- Keep proper footing and balance at all
times.
14 Maintain tools with care
- Keep cutting tools sharp and clean for better
and safer performance.
- Follow instruction for lubricating and chang-
ing accessories.
- lnspect tool cords periodically and if dam-
aged have them repaired by an authorized
service facility.
- lnspect extension cords periodically and re-
place if damaged.
- Keep handles dry, clean and free from oil
and grease.
15 Disconnect tools
- When not in use, before servicing and when
changing accessories such as blades, bits
and cutters, disconnect tools from the power
supply.
If the planer shaft blocked when working by
excessive feed force or clamping the work
piece, turn off the device and disconnect it
from the mains plug. Remove the workpiece
and make sure that the planer shaft runs
freely. Turn the power on, and run the op-
eration again with reduced feed force.
16 Remove adjusting keys and wrenches
- Form the habit of checking to see that keys
and adjusting wrenches are removed from
the tool before turning it on.
17 Avoid unintentional starting
- Ensure switch is in "off' position when plug-
ging in.
18 Use outdoor extension leads
- When the tool is used outdoors, use only
extension cords intended for outdoor use
and so marked.
19 Stay alert
- Watch what you are doing, use common
sense and do not operate the tool when you
are tired.
20 Check damaged parts
- Before further use of tool, it should be care-
fully checked to determine that it will oper-
ate properly and perform its intended func-
tion.
- Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation.
- A guard or other part that is damaged
should be properly repaired or replaced by
an authorized service centre unless other-
wise indicated in this instruction manual.
- Have defective switches replaced by an au-
26 GB
thorized service centre.
- Do not use the tool if the switch does not
turn it on and off.
21 WARNING!
- The use of any accessory or attachment oth-
er than one recommended in this instruction
manual may present a risk of personal injury.
22 Have your tool repaired by a qualified person
- This electric tool complies with the relevant
safety rules. Repairs should only be carried
out by qualified persons using original spare
parts, otherwise this may result in consider-
able danger to the user.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
SPECIAL SAFETY INSTRUCTIONS
• Do not use blunt knives. Risk of kick-back.
• The cutter block must be fully covered.
• Use a push stick to plane any short workpieces.
• Take additional safety precautions if you are plan-
ing any narrow workpieces. It may be necessary
to use lateral pressure equipment and springload-
ed covers to ensure that you can work in safety.
• The machine is not suitable for cutting rebates.
• The anti-kick safeguard and the infeed roller must
be inspected at regular intervals.
• Machines fitted with a sawdust extractor and
extractor hoods must be connected to the devices
concerned. The type of material used can have a
negative influence on the dust generated.
• The machine is designed exclusively for the cut-
ting of wood and similar materials.
• The knife must be replaced immediately once it
becomes worn down by 5%.
• If a push stick is not used there may be a risk of
serious danger. The push stick should always be
kept at the machine when not used.
• There is a greater risk of danger when small work-
pieces are fed in by hand. Always observe the manu-
facturer's instructions on the use of the push stick.
• If the safety covers, infeed table or mesh are in-
correctly aligned they could lead to uncontrollable
situations.
• Damaged or soiled workpieces may cause a risk
of danger. Never use metal parts in the machine or
any materials which can fracture or shatter. Risk
of injury!
• To cut long workpieces, always place them on a
mobile table or similar type of supporting equip-
ment. Otherwise there is a risk that you may lose
control over the workpiece.
• The machine is only suitable for planing and thick-
nessing.
• Wear suitable protective clothing when working
with the machine: