Publicité
Les langues disponibles
Les langues disponibles
- Wood glue UHU wood, waterproof, 75g (or-
der No. 48515)
- Two-component glue UHU plus Acrylit, 30g
(order No. 48315)
- Super putty micro-fill white 295 ml (order No.
80480)
- Pore filler (Lord Nelson pore filler, order No.
80110)
- Clear coat, silk-matt (order No. 80112)
- Mahogany stain (order No. 349111)
- Colour spray, antique white (order No.
320012), camouflage brown 27 (order No.
316027) or blue 210 (order No. 316210),
light grey (primer coat), and white (order No.
320010)
- Masking tape (order No. 493269)
- Ballast (order No. 60108) 7 packs, 500g each
The following tools are the basic equipment for
building the "Antares":
- Craft knife (order No. 416002)
- Hand Drill (order No. 473841)
- Broach (order No. 491016)
- Sanding block (order No. 490080)
- Sandpaper grit 180, 320, 400 and 600 (set
order No. 490190)
- Round file approx. diameter 6 mm
- Drill bit diameter 1 mm, 1.5 mm, 2 mm, 3
mm, 4 mm, 6 mm
- Wet and dry sandpaper 400 and 600 for pore
filler, primer coat and paint
- Diagonal cutting pliers (order No. 455550)
- Building board (most suitable wood core ply-
wood 115 cm x 30 cm)
For masking when painting, PVC masking tape
or paper masking tape is also required. The
Krick range includes suitable masking tape
under order No. 493269. This masking tape is
available in various widths. Do not use crepe
tape!
To equip the model with a remote control and
sailing operations, the following additional
equipment is required:
Variant I
- 4-channel remote control with servo
- Sail winch for mainsail Windforce 1406 MG
order No. 79074
- Sail winch for headsail Windforce 1006 MG
order No. 79073
Variant II
- 6-channel computer – remote control with
servo
- Sail winch for mainsail Windforce 1406 MG
order No. 79074
- Sail winch for headsail, port side
Windforce 1006 MG order No. 79073
- Sail winch for headsail, starboard side
Windforce 1006 MG order No. 79073
Updated June 2016
If you also want to use the special function
-
auxiliary drive,
The following parts will be required:
-
Propulsion set (order No. 42370)
-
Speed controller at least 20 A, for-
wards/backwards with BEC receiver
power supply (order No. 67051)
-
Drive battery 7.2 V or Lipo 7.4 V
-
Charger
The numerous photos in the building sections
make building the model simpler.
To identify the individual laser-cut components,
you will find the overview diagram at the end of
these instructions helpful. Before starting con-
struction, you should clearly identify these
parts using the parts list, building instructions
and building plan and number them with a soft
pencil. When building the model, always care-
fully remove only the parts that you need at the
specific time, using a sharp craft knife.
You will find it much easier to get into boat
model building if you contact an experienced
model builder who will help you if you have any
questions and problems and will make sure
that your own "Antares" becomes a functioning
and beautiful model. If you do not have an
experienced model builder in your group of
friends and/or acquaintances, contact your
local model boat building club or ask for the
address of the club from the specialist model
building retailer from whom you purchased this
set. At the model boat building club, you will
find active model builders, who will certainly be
happy to help.
Note: Some of the photos used are images
of the prototypes and in some cases do not
match the components used or the compo-
nents in the kit.
We hope you have a lot of fun building your
gaff cutter yacht.
Page 2
©
Krick Modelltechnik Knittlingen
Publicité
