Variants; Main Features; Sterilisation Programs; Test Programs - Faro NISEA Basic Mode D'emploi

2.1 Variants

The following autoclave variants are available:
Version
Chamber size
Power supply
REF Cycles B
REF Cycles B Switzerland
REF Cycles S
REF Cycles S Switzerland
REF Cycles B + S
REF Cycles B + S Switzerland
Version
Chamber size
Power supply
REF Cycles B
REF Cycles B Switzerland
REF Cycles S
REF Cycles S Switzerl
REF Cycles B + S
REF Cycles B + S Switzerland
XXX: they mean an aesthetic personalization or a thermodynamic cycle already validated.

2.2 Main features

The vacuum pump ensures an optimal sterilisation process in which the steam interacts properly with the load being
processed, including any cavities.

2.2.1 Sterilisation programs

●
Type B
- 134°C Standard
- 134°C Prion
- 134°C B-Flash
- 121°C Standard
●
Special cycle
- Drying only
●
Type S
- 134°C Universal S
- 134°C Softprogramm

2.2.2 Test programs

checks the ability to hold a vacuum
- Vacuum test:
checks steam penetration into porous loads
- Bowie & Dick test:
- 121 or 134°C Helix test: checks steam penetration into hollow loads
The autoclave is available with the following storage devices:
- USB port (USB peripheral not supplied).
- RS-232 port (for Faro printer, NOT supplied).

2.2.3 Water filling systems

Automatic: with the aid of a pump inside the autoclave.
Mains connection possibility of connecting a demineralisation system, to increase autonomy. It must be installed by
an authorised technician.
Manual: as an alternative, the device is equipped with a manual emergency filling system at the FRONT (9 fig. 1).

2.2.4 Automatic sterilisation parameter control

During sterilisation, the pressure, temperature and time are continuously monitored by an automatic process control
system.

2.2.5 Motorised closure

The autoclave has a motorised closure system to ensure a good seal. It is based on a screw and nut screw. Closure
works with a pre-locking mode that activates when the door is shut. The door is only closed fully when the cycle starts.

2.2.6 Bio-X filter

This injects sterile air into the chamber during the drying and pressure balancing phases.
18
220 V 230 V
60 Hz 50/60 Hz
750 030XXX 750 000XXX 750 020XXX 750 130XXX 750 100XXX 750 120XXX
// 750 010XXX
750 031XXX 750 001XXX 750 021XXX 750 131XXX 750 101XXX 750 121XXX
// 750 011XXX
750 032XXX 750 002XXX 750 022XXX 750 132XXX 750 102XXX 750 122XXX
// 750 012XXX
Premium
18
220 V 230 V
60 Hz 50/60 Hz
751 030XXX 751 000XXX 751 020XXX 751 130XXX 751 100XXX 751 120XXX
// 751 010XXX
751 031XXX 751 001XXX 751 021XXX 751 131XXX 751 101XXX 751 121XXX
// 751 011XXX
751 032XXX 751 002XXX 751 022XXX 751 132XXX 751 102XXX 751 122XXX
// 751 012XXX
Basic
240 V 220 V
50 Hz 60 Hz
// // 750 110XXX
// // 750 111XXX
// // 750 112XXX
23
240 V 220 V
50 Hz 60 Hz
// // 751 110XXX
// // 751 111XXX
// // 751 112XXX
23
230 V 240 V
50/60 Hz 50 Hz
//
//
//
230 V 240 V
50/60 Hz 50 Hz
//
//
//
45 45