Appendix; Selection Of Tip; Servicing And Cleaning Of Airless Hard-Metal Tips; Accessories - Titan PowrLiner 2850 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

PL2850
8

APPENDIX

8.1

SELECTION OF TIP

To achieve faultless and rational working, the selection of the
tip is of the greatest importance.
In many cases the correct tip can only be determined by means
of a spraying test.
SOME RULES FOR THIS:
The spray jet must be even.
If streaks appear in the spray jet the spraying pressure is either
too low or the viscosity of the coating material to high.
REMEDY: Increase pressure or dilute coating material. Each
pump conveys a certain quantity in proportion to the size of
the tip:
The following principle is valid:
There is a large range of tips with various spraying angles.
8.2
SERVICING AND CLEANING OF AIRLESS
HARD-METAL TIPS
STANDARD TIPS
If a different tip type has been fitted, then clean it according to
manufacturer's instructions.
The tip has a bore processed with the greatest precision. Careful
handling is necessary to achieve long durability. Do not forget
the fact that the hard-metal insert is brittle! Never throw the tip
or handle with sharp metal objects.
The following points must be observed to keep the tip
clean and ready for use:
1. Follow the "Pressure Relief Procedure" found in the
Operation section of this manual, section 4.5.
2. Remove the tip from the spray gun.
3. Place tip in an appropriate cleaning agent until all coating
material residue is dissolved.
4. If there is high-pressure air available, blow out tip.
5. Remove any residue by means of a sharp wooden rod
(toothpick).
6. Check the tip with the help of a magnifying glass and, if
necessary, repeat points 3 to 5.
large tip = low pressure
small tip = high pressure
8.3

ACCESSORIES

PART NO.
DESCRIPTION
SPRAY GUNS
0538104
RX-80 with striping tip
0538005
RX-80 4 finger with TR-1 Tip
0538006
RX-80 2 finger with TR-1 Tip
0550060
S-3 spray gun
SPRAY TIPS AND ACCESSORIES
697-xxx
TR-1 striping tip*
694-xxxxxxx
TR-2 striping tip*
0289228
No Build Tip Guard
651-139
Tip Swivel
661-020
Tip seat and seal kit (5 pack)
FILTERS
0089957
Coarse Mesh Filter (Green)
0089958
Medium Mesh Filter (White)
0089959
Fine Mesh Filter (Yellow)
0089960
Extra Fine Mesh Filter (Red)
LINE STRIPER ACCESSORIES
759-130
Paint Hopper
0290038A
LineSite
759-150
Side Striper
424-826
Bead Dispenser, 1st Gun Kit, 4–6" line width
424-840
Bead Dispenser, 1st Gun Kit w/Hopper, 12" line
width
0290181
Bead Dispenser bracket kit (required for Bead
Dispenser)
0290180
Ball hitch kit
0290182
Hitch bracket (required for LazyLiner)
0290040
LazyLiner Elite
0290041
LazyLiner Pro
0290953
HandiBead
0290623
Spray Shield
0290932
Stencil kit 1
0290933
Stencil kit 2
0290934
Stencil kit 3
LUBRICANTS AND CLEANERS
314-482
Liquid Shield™ 1 Quart
0297055
Pump Shield™, 12 oz.
0508071
Paint Mate 1 Quart
* Go to www.titantool.com for tip sizes
REPAIRS
33

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

02900080290009

Table des Matières