Accessories - Festool KSC 60 EB Notice D'utilisation

English
CAUTION
Risk of injury!
The power tool may slip out of your hands
when you are carrying it.
► Always carry the power tool with both
hands, using the carrying handles [16] pro­
vided on both sides of the power tool.
11.1 Securing the machine (transport
position)
► Remove the battery pack from the power
tool.
► Move the saw unit into the rear position and
lock it in place using the rotary knob [1-6].
► Swivel the saw unit into a vertical position.
▷ Loosen the star handle [2-6].
▷ Move the saw unit into a vertical posi­
tion.
▷ Tighten the star handle.
► Lock the saw unit in place.
▷ Press and hold the safety button [1-3].
▷ Move the saw unit downwards until it
reaches the limit stop.
▷ Pull the lever for the transport locking
device [1-7].
▷ Release the safety button.
The saw unit remains in the lower position.
► Swivel the rotary base into the right-hand
position.
▷ Release the rotary knob [1-14].
▷ Press and hold the detent lever [1-13].
▷ Swivel the rotary base [1-15] as far to
the right as it will go.
▷ Release the detent lever, close the rota­
ry knob.
The machine is in the transport position [16].
11.2 Carrying handles provided
– Handle on the saw unit [16-1]
– Handle on the key storage box [16-3]
– Extension tables [16-2] (when fixed in
place)

12 Accessories

The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet at "www.festool.com".
In addition to the accessories described,
Festool also provides a comprehensive range of
system accessories that allow you to use your
saw more effectively and in diverse applica­
tions, e.g.:
• KA-KS60 trimming attachment
36
• UG-KAPEX KS 60 underframe
• UG-KS UNI underframe
• A-SYS-KS60 screw-in feet
• Clamping connection for MFT SZ-KS
• SM-KS60 bevel
12.1 Bevel SM‑KS60 (available as an
accessory depending on the model)
The bevel can be used to gauge any angle (e.g.
between two walls). The bevel therefore forms
the angle bisection.
Gauging the interior angle [17A]
► Open the locking device [17-2].
► Swivel the router [17-1] out in order to
gauge the interior angle.
► Close the locking device.
The dashed mark [17-4] provides the angle bi­
section. The angle bisection can be transferred
via the outside edges of the bevel to the position
markings on the rotary base.
Gauging the exterior angle [17B]
► Open the locking device [17-2].
► Slide the aluminium profiles [17-3] on the
router forwards.
► Swivel the router [17-1] out so that the alu­
minium profiles are at the exterior angle.
► Close the locking device.
► Slide the aluminium profiles for the two
routers back again.
Transferring the angle [18]
► Place the bevel perfectly in place on one of
the stop rulers
your thumb.
► Release the rotary knob
► Hook in the detent lever
► Swivel the rotary base
edge of the bevel is congruent with the
marking .
To do so, the bevel must be positioned so
that it is parallel to the stop of the com­
pound mitre saw. At the same time, apply
pressure to the stop ruler by pressing in
the recessed grip with your thumb.
► Close the rotary knob
The angle is transferred, the sawing process
can be started.
12.2 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli­
cations and these are specially designed for
your Festool saw.
and press down with
.
.
, until the outside
, remove the bevel.