Accessories - Festool SYMMETRIC SYM 70 E Notice D'utilisation D'origine

The machine is equipped with self-disconnecting
special carbon brushes. If they are worn, power is
interrupted automatically and the machine comes
to a standstill.
• Clean the tabletop insert [1.9] regularly and re-
move wood chips, dust deposits and workpiece
offcuts from the extraction channel on the chip
defl ector (see Fig. 6).
9.1 Replacing table insert
Never work with a worn table insert (1.9) but
replace it with a new one. To do this, release the
fi ve screws used to fasten the table insert on the
saw table.
A new table insert is supplied without a saw slot.
You will therefore fi rst have to saw a slot follow-
ing installation.
9.2 Adjusting the saw unit
The swivelling range of the saw unit can be read-
justed using the screw (6.2). This may be neces-
sary if the diameter of the saw blade alters during
sharpening or if a new saw blade is fi tted.
– Set the sliding fence (6.4) to 0°.
– Release the lock nut (6.1).
– Swivel the saw unit downwards until it reaches
the fence.
– Adjust the saw unit by turning the screw (6.2)
as shown in illustration 7 (turn to the left - saw
unit is lowered; turn to the right - saw unit is
raised).
The saw unit must not be set so deep that
it can saw into the saw table.
– Tighten the lock nut again.
10

Accessories

Use only original Festool accessories and Festool
consumable material designed for this machine
because these components are designed spe-
cifi cally for the machine. Using accessories and
consumable material from other suppliers will
most likely affect the quality of your working
results and limit any warranty claims. Machine
wear or your own personal workload may increase
depending on the application. Protect yourself and
your machine, and preserve your warranty claims
by always using original Festool accessories and
Festool consumable material!
The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet under www.festool.com.
All manuals and user guides at all-guides.com
17
11 Disposal
Do not throw the power tool in your household
waste! Dispose of the machine, accessories and
packaging at an environmentally-responsible
recycling centre! Observe the valid national regu-
lations.
EU only: European Directive 2002/96/EC stipulate
that used electric power tools must be collected
separately and disposed of at an environmentally
responsible recycling centre.
12 Warranty
For our tools, we give warranty for material and
production defects in accordance with the locally
applicable legal provisions, but in any case for at
least 12 months. Within the EU member states,
the warranty period is 24 months (verifi cation
through invoice or delivery note).
Damage caused by, in particular, natural wear,
overloading, incorrect handling, or damage caused
by the operator, or damage caused through use
of the equipment contrary that specifi ed in the
Operating Instructions, or damage which was
known at the time of purchase, is not covered by
the warranty.
Furthermore, damage caused by the use of non-
original Festool accessories and consumable
material (e.g. sanding pads) is also excluded.
Complaints can only be recognised if the tool is re-
turned while still assembled to the supplier or an
authorised Festool Customer Service workshop.
Keep the Operating Instructions, Safety Instruc-
tions, Spare Parts List and purchase receipt in a
safe place.
Otherwise the respective, current warranty condi-
tions of the manufacturer shall apply.
Note
Due to continuous research and development
work, we reserve the right to make changes to the
technical content of this documentation.
REACH for Festool products, their accessories
and consumables
REACh is a European Chemical Directive that
came into effect in 2007. As "downstream users"
and product manufacturers, we are aware of our
duty to provide our customers with information.
We have set up the following website to keep you
updated with all the latest news and provide you
with information on all the materials used in our
existing products: www.festool.com/reach