Technical Specifications Of Product Components - Nice MhouseKit WG2W Instructions Et Avertissements Pour L'installation Et L'utilisation

WG2W is manufactured by Nice S.p.a. (prov. of Treviso – Italy). In order to improve its products, Nice S.p.a. reserves the right to modify their technical
characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes. Note:
all the technical characteristics refer to a temperature of 20°C.
CL2W command control unit
Type
Technology adopted
Maximum cycles frequency
Maximum continuous cycle time
Mains power supply
Nominal absorbed power
Emergency power supply
Motors output
Flasher output
ECSBus output
"OPEN" input
"STOP" input
Radio Antenna input
Maximum cable length
Ambient operating temperature
Use in acid, saline or potentially
explosive atmospheres
Mounting
Protection rating
Dimensions / weight
Remote control compatibility
Memorisable GTX4 transmitters
Range of the GTX4 transmitters
Programmable functions
Self-programming functions
Radio protocol
Radio communication
Installable wireless accessories
Installable PH100W photocells
30 – English

TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS

Command control unit for 1 or 2 24Vdc motors for automation of automatic gates or doors, complete
with radio receiver for "GTX4" transmitters
Electronic board governed by an 8 Bit microcontroller with flash technology. A transformer inside the
control unit, but separated from the board, reduces the mains voltage to the nominal 24V voltage used
in all of the automation system
30 cycles/hour
230Vac (+10% -10%) 50/60Hz
120W; at peak the power is 310W for a maximum duration of 2s
Provision for "PR1" buffer battery connection
2, for 24Vdc motors with a nominal current of 1.1A, at peak power the maximum current is 3.5 A for
a maximum duration of 2 s
For normally open contacts (the closing of the contact causes the "OPEN" command)
For normally closed or normally open contacts and/or for constant resistance of 8.2 KΩ, or normally
closed contacts with self-recognition of the "normal" state (any variation from the memorised status
causes the "STOP" command)
50 Ω for RG58 or similar type of cable
Mains power supply: 30m; motors outputs: 10m; other inputs/outputs: 20m with antenna cable pref-
erably shorter than 5m (observe the warnings regarding minimum gauge and type of cables)
-20 ÷ 50°C
No
Vertical, wall-mounted
IP44
180 x 240 h 110mm / 2.8 kg
Using "GTX4" transmitters, the control unit is able to receive one or more of the following commands:
"OPEN", "Partial Open", "Open Only" and "Close Only"
Up to 256 if memorised in mode 1
From 50 to 100m. This range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flasher
Using "GTX4" transmitters, the control unit is able to receive one or more of the following commands:
"OPEN", "Partial Open", "Open Only" and "Close Only"
Up to 150 if memorised in mode 1
From 50 to 100m. This range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flasher
"Cycle" or "Complete cycle" (automatic closure) functionality
"Slow" or "fast" motors speed
Pause time during "complete cycle", selectable from 10, 20, 40, 80 seconds
Partial opening type selectable in 4 modes
Obstacle detection system sensitivity, 4 selectable levels
"Open" command functionality selectable in 4 modes
Autodetection of Power&Free radio System devices from Mhouse
Recognition of the type of "STOP" device (NO or NC contact or 8.2 KΩ constant resistance)
Recognition of the manoeuvre length for each motor
Automation recognition with 1 or 2 motors
High security; compatible with the Power&Free System radio technology from Mhouse
Bidirectional, on 7 channels in band 868 MHz.
Maximum 20 units
Maximum 6 pairs