Technical Data - caprari PM50 Notice D'utilisation Et D'entretien

Faults
5. The unit absorbs
excessive power.
6. The unit delivers a
decidedly poor flow
rate.
7. Although the unit
operates, it delivers
absolutely no water.
8. The unit is noisy and
vibrates.
9. The unit fails to
automatically stop.
10. The seal on the shaft
drips excessively.
Caprari S.p.A.
SALES NETWORK and LIST OF ASSISTANCE CENTERS available in www.caprari.com
Probable causes
5.1. Excessive rotation speed.
5.2. The unit cannot freely turn owing to abnormal
friction.
5.3. The unit is not perfectly aligned.
5.4. The packing gland is too tight.
5.5. Excessive flow rate during operation.
6.1. Air has entered through the suction port.
6.2. The electric motor turns in the wrong direction.
6.3. The check valve or foot valve have blocked in
a partially closed position.
6.4. Worn pump.
6.5. Sluice valve partially closed.
6.6. Pump operating at cavitation rate.
6.7. The strainer is clogged by foreign bodies.
6.8. Rotation speed too low.
7.1. Pump unprimed owing to insufficient head.
7.2. Pump unprimed owing to excessive flow rate.
7.3. The check valve or foot valve are blocked in a
closed position.
7.4. Closed sluice valve.
7.5. Pump excessively worn.
7.6. Worn transmission coupling owing to the high
number of work hours and/or too many starts/
hour and/or bad alignment.
7.7. Strainer clogged by foreign bodies.
7.8. Rotation speed too low.
8.1. Incorrect plant installation.
8.2. Water containing a high amount of gas.
8.3. Worn bearings.
8.4. Incorrect assembly of the components or plant
installation.
8.5. Pump operating at cavitation rate.
8.6. Stress transmitted from the pipes to the pump
casing.
9.1. Insufficient flow rate of the unit.
9.2. The automatic monitoring devices of the plant
or motor fail to enable the unit to stop.
10.1.The seal is no longer efficient.
Remedies
5.1. Regulate the internal combustion engine.
Make sure that the pump/electric motor combi-
nation has been correctly selected.
5.2. Send the unit to an authorized after-sales
service center.
5.3. Check the alignment as described in paragraph
5.3 "Mechanical connections".
5.4. Adjust the packing gland by working evenly on
both nuts in order to ensure a slight dripping
during operation.
5.5. Check and reduce if necessary, by means of
the sluice valve on the delivery pipe.
6.1. Increase the level of the liquid at the suction
port.
6.2. Invert two of the three phases.
6.3. Disassemble the valve from the pipe and check.
6.4. Send the pump to an authorized after-sales
service center.
6.5. Open the sluice valve.
6.6. Compare the pressure on the suction side with
the NPSH values given in the specific technical
documentation.
6.7. Remove the obstruction.
6.8. Regulate the internal combustion engine.
Make sure that the pump/electric motor
combination has been correctly selected.
7.1. See 6.1.
7.2. Make sure that the right product has been
selected.
Reduce the flow rate by means of the sluice
valve on the delivery duct.
7.3. See 6.3.
7.4. Regulate the sluice valve.
7.5. See 6.4.
7.6. Make sure that the elastic components are in a
good condition and replace them if necessary
(consult paragraph 6.3 "Maintenance").
7.7. See 6.7.
7.8. See 6.8.
8.1. See 6.1.
8.2. See 6.1.
8.3. See 6.4.
8.4. Check according to the specifications in
paragraph 5.3 "Mechanical connections".
8.5. See 6.6.
8.6. Check the maximum stress values given in the
"Flange stress" table in chapter 11 "Technical
data".
Connect the pump to the pipes by means of
compensation joints.
9.1. Make sure that the right unit has been chosen.
Also consult 6.3, 6.4 and 6.5.
9.2. See 1.3.
10.1.Replace the seal as described in paragraph 6.3
"Maintenance".
Send the unit to an authorized after-sales
service center if necessary
PM
GB
21