Ryobi RDP102L Manuel D'utilisation page 15

EN
FR DE ES IT NL
mounting board should be of sufficient size to avoid tipping
while drill press is in use. Any good grade plywood or
chipboard with a 19 mm (3/4") thickness is recommended.
1. Mark holes on surface where drill press is to be
mounted using holes in drill press base as a template
for hole pattern.
2. Drill holes through mounting surface.
3. Place drill press on mounting surface, aligning holes
in the base with holes drilled in the mounting surface.
4. Insert bolts (not included) and tighten securely with
lock washers and hex nuts (not included).
If lag bolts are used, make sure they are long enough
to go through holes in drill press base and material the
drill press is being mounted to. If machine bolts are
used, make sure bolts are long enough to go through
holes in drill press, the material being mounted to, and
the lock washers and hex nuts.
notE: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of
the workbench.
Once the drill press is securely mounted on a sturdy
surface:
1. Check for vibration when the motor is switched ON.
2. Adjust and retighten the mounting hardware as
necessary.
3. Check the table assembly to assure smooth movement
up and down the column.
4. Check to assure that the spindle shaft moves smoothly.
cHucK KEy storaGE
See Figure 17.
Storage holder for the chuck key is located on the right
side of the drill press.
BEvEl DrillinG
See Figure 18.
notE: A bevel scale has been included to measure
approximate bevel angles. If precision is necessary, a
square or other measuring tool should be used to position
the table. To use the bevel scale:
1. Tighten the nut on the locking pin using a 10 mm or
adjustable wrench clockwise to release the pin from
its table support. This pin will be needed when placing
the table back to its 0 degree setting from the table
support. Do not throw away.
2. Loosen the large hex head table bevel locking bolt
using a 17 mm or adjustable wrench.
3. Tilt the table, aligning the desired angle measurement
to the zero line opposite the scale.
4. Tighten the table bevel locking bolt.
5. To return the table to its original position, loosen the
cable bevel locking bolt. Return the table to the 0°
position.
PT DA SV FI NO RU
English
PL CS HU RO LV LT
6. Return nut on locking pin to the outside end of threads.
Gently tap locking pin, using a rubber mallet, until it is
seated in the mating hole of the table bracket. Hand
tighten nut.
notE: The table has been removed from the
illustration for clarity.
To prevent personal injury, always disconnect the plug
from the power source when making any adjustments.
spinDlE / Quill
See Figure 20.
Rotate the feed handles counterclockwise to lower spindle
to its lowest position. Hold the chuck and move it front to
back. If there is excessive play, proceed with the following
adjustments:
1. Loosen the lock nut located on the right side of the drill
press, using a 10 mm wrench.
2. Turn the screw clockwise to eliminate the play, using a
slotted screwdriver, but without obstructing the upward
movement of the spindle. (A little play in the spindle
is normal.)
3. Tighten the lock nut.
Quill rEturn sprinG
See Figure 21.
The quill return spring may need adjustment if the quill
return speed is too rapid or too slow. This spring is located
on the left side of the drill head.
1. Lower the table for additional clearance.
2. Place a screwdriver in the lower front notch of the
spring cap. Hold it in place while loosening and
removing only the outer jam nut, using a 10 mm
wrench.
3. With the screwdriver still engaged in the notch, loosen
the inner nut just until the notch disengages from the
boss on the drill press head.
notE: Do not remove this inner nut, because the
spring will forcibly unwind.
4. Carefully turn the spring cap counterclockwise with the
screwdriver, engaging the next notch.
5. Lower the quill to the lowest position by rotating the
feed handle in a counterclockwise direction while
holding the spring cap in position.
6. If the quill moves up and down as you desire, tighten
the inner nut sung against the spring cap and spring
cap with the wrench. If too loose, repeat steps 3
through 5 to tighten. If too tight, reverse steps 4 and 5.
7. Secure the outer nut against the inner nut with the
wrench.
7
ET HR SL SK BG UK
warninG
TR EL