Residual Risks - Ryobi RDP102L Manuel D'utilisation

EN
FR DE ES IT NL
■ warning. The use of any accessory or attachment
other than the one recommended in this instruction
manual may present a risk of personal injury.
■ Have your tool repaired by a qualified person.
This electric tool complies with the relevant safety
rules. Repairs should only be carried out by qualified
persons using original spare parts otherwise this may
result in considerable danger to the user.
Drill prEss safEty warninGs
■ Keep bits clean and sharp. Sharp bits minimize
stalling. Dirty and dull bits may cause misalignment of
the material and possible operator injury.
■ Keep hands away from work area. Keep hands
away from the bit. Restrain any loose clothing, jewelry,
long hair, etc., That may become entangled in the bit.
■ always clamp workpiece or brace against column
to prevent rotation. Never use your hand to hold the
object while drilling.
■ use recommended speed for drill accessory and
workpiece material.
■ Be sure drill bit or cutting tool is securely locked
in the chuck.
■ Be sure chuck key is removed from the chuck before
connecting to power source or turning power on.
■ adjust the table or depth stop to avoid drilling into
the table. Shut off the power, remove the drill bit, and
clean the table before leaving machine.
■ avoid direct eye exposure when using the laser
guide.
■ always ensure the laser beam is aimed at a surface
without reflective properties.
materials are not suitable for laser use.
■ never place your fingers in a position where they
could contact the drill or other cutting tool if the
workpiece should unexpectedly shift.
■ never perform any operation by moving the head
or table with respect to one another. Do not turn the
motor switch on or start any operation before checking
that the head and table support lock handle is clamped
tight to column and head and table support collars are
correctly positioned.
■ Before engaging the power switch, make sure
the belt guard is down and the chuck is installed
properly.
■ lock the motor switch off when leaving the drill
press. Do not perform layout, assembly, or set-up
work on the table while the cutting tool is rotating,
switched on, or connected to a power source.
■ if the power supply cord is damaged, it must be
PT DA SV FI NO RU
English
Shiny reflective
PL CS HU RO LV LT
replaced only by the manufacturer or by an authorised
service centre to avoid risk.
■ store idle tools. When not in use, tools should
be stored in a dry locked-up place, out of reach of
children.
■ save these instructions. Refer to them frequently
and use to instruct other users. If you loan someone
this tool, loan them these instructions also.
Basic opEratinG instructions
To get the best results and minimize the likelihood of
personal injury, follow these instructions for operating your
drill press.
For your own safety, always read the safety instructions
listed within this operator's manual.
lasEr safEty rulEs
■ The laser radiation used in this saw is Class 2 with
maximum ≤1mW and 650nm wavelengths. Do not
stare into the laser beam. Failure to comply with the
rules could result in serious personal injury.
■ Do not stare into beam during operation.
■ Do not project the laser beam directly into the eyes of
others. Serious eye injury could result.
■ Do not place the laser in a position that may cause
anyone to stare into the laser beam intentionally or
unintentionally.
■ Do not use optical tools to view the laser beam.
■ Do not operate the laser around children or allow
children to operate the laser.
■ Do not attempt to repair the laser device by yourself.
■ Do not attempt to change any parts of the laser device
by yourself.
■ Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
■ Do not replace the laser with a different type.

rEsiDual risKs

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The operator should pay particular and additional
attention to these points in order to reduce the risk of
serious personal injury.
■ Injury to hearing – Wear suitable ear protection and
limit exposure.
3
ET HR SL SK BG UK
warninG
TR EL