Maintenance And Repair - Ryobi CLT1830B Manuel D'utilisation

GB GB
F F D D E E
OPERATING TIPS
Clear the area to be cut before each use. Remove
Q
all objects such as rocks, broken glass, nails, wire,
or string which can be thrown or become entangled in
the string head.
Keep the string trimmer tilted toward the area
Q
being cut. Avoid digging into grass.
Slowly move the string trimmer in and out of the area
Q
being cut.
Use the tip of line to do the cutting - do not force
Q
string head into uncut grass.
Cut tall grass from the top down. This will prevent
Q
grass from wrapping around the string head that may
cause damage from overheating. If grass or other
debris becomes wrapped around the string head,
STOP THE MOTOR by releasing the trigger and allow
the string head to stop spinning. Remove the battery
pack and then remove the grass or debris.
Wire and picket fences cause extra line wear, even
Q
breakage. Stone and brick walls, curbs, and wood
may wear line rapidly. Walk around trees and shrubs.
Tree bark, wood mouldings, siding, and fence posts
can easily be damaged by the line.
Keep the string trimmer tilted toward the area
Q
being cut. To trim around trees, posts, fences, etc.,
keep the string trimmer at a 30° degree angle.
See Figure 12.
USING THE STRING TRIMMER FOR
EDGING/VERTICAL CUTTING
For vertical cutting/edging pull the edging coupler
Q
(Fig. 1 – L) and rotate the motor housing (Fig.1 - E)
180 degree. Release the edging coupler (Fig. 1 – L)
which snaps into the edging position easily.
Flip the edging wire (Fig. 1 –M) down for the edging.
Q
Lift the trimmer by both handles and turn it into
Q
cutting/edging position.(Fig.9.b)

MAINTENANCE AND REPAIR

WARNING
When servicing use only identical replacement
parts. Use of any other parts can create a hazard
or cause product damage. Avoid using solvents
when cleaning plastic parts. Most plastics are
susceptible to damage from various types of
commercial solvents and may be damaged by
their use. Use a clean cloth to remove dirt, oil,
grease, etc.
CAUTION
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. They contain
I I P P NL NL S S DK DK N N FIN GR HU FIN GR HU CZ RU CZ RU
English
CUTTING LINE REPLACEMENT
The cutting line may be replaced by either rewinding the
existing spool or installing a convenient prewound spool.
REWINDING THE EXISTING SPOOL
See Figure 14.
Remove the battery pack from the string trimmer.
Q
Press in the tabs on each side of the spool cap.
Q
Remove the spool cap and spool. Discard any
Q
remaining line on the spool.
NOTE: If the spring falls off the spool housing during
this procedure, reinstall the spring before installing
the spool and spool cap.
Inspect the string head for damaged or worn parts
Q
and clean thoroughly.
Using approximately 3 m (10 feet) of new cutting line,
Q
insert one end of the line into the slot on the spool.
Ensure the end of the line is pushed all the way
towards the inner side of slot.
NOTE: No more than 3.175 mm (1/8 in.) of the line is
to protrude from the slot.
Wind the line, in even and tight layers, onto the spool.
Q
Line should be wound in the direction of the arrow
indicated on the spool.
Unwind approximately 102 mm (4 in.) of the line from
Q
the spool. Hold the line and spool firmly to keep it
from unwinding then place the spool cap onto the
spool.
Holding the spool cap and spool by the bump knob,
Q
place into the spool housing and insert cutting line
into the opening in spool housing.
NOTE: Tabs on the spool cap should be aligned with
the slots in the spool housing.
While pressing in the tabs, push down the spool cap
Q
and spool to lock in place.
Completely assembled string head should appear as
Q
shown. See Figure 15.
INSTALLING A PREWOUND SPOOL
See Figure 14.
Remove the battery pack from the string trimmer.
Q
16
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT
chemicals that may damage, weaken, or destroy
plastics.
WARNING
Use only 1.65 mm (0.065 in) diameter genuine
replacement line. Never use metal reinforced
line, wire, or rope, etc. These can break off and
become a dangerous projectile. Do not use any
other attachment on this unit.
LV LV SK BG SK BG