Ryobi CLT1830B Manuel D'utilisation page 20

GB GB
F F D D E E
Fig. 14
A. BUMP KNOB
B. SLOT ON SPOOL
C. SPOOL CAP
D. TABS
E. SPOOL
F. SPRING
G. SPOOL HOUSING SLOT
H. OPENING IN SPOOL HOUSING
I. SPOOL HOUSING
Fig. 16
A. BATTERY CHARGER
B. GREEN LIGHT
C. RED LIGHT
ASSEMBLY
INSTALLING GRASS SHIELD
Remove both screws on the motor housing.
Q
Orient grass shield on the motor housing and twist to
lock in place as shown.
Re-install screws to secure grass shield in place.
Q
See Figure 2.
ATTACHING THE FRONT HANDLE
Press the front handle onto the shaft. See Figure 3.
Move it to a position on the shaft suitable for the user.
Secure it with the bolt, wing knob and washers in the
sequence as shown.
Tighten the bolt to ensure the handle is fixed firmly.
ADJUSTING THE SHAFT
Rotate the lower portion of the shaft adjustment collar
Q
to the "Unlock" position. See Figure 4.
Lower shaft should now be free to slide down from
Q
inside the upper shaft. Make sure the shaft is pulled
out to the desired position. See Figure 5.
Rotate shaft adjustment collar to the "Lock" position
Q
and tighten securely. See Figure 6.
WARNING
If any parts are missing, do not operate unit until
the missing parts are replaced. Failure to do so
could result in possible serious personal injury.
OPERATION
LED FUNCTIONS OF CHARGER
See Figure 16.
LED WILL BE ON TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
Red LED on = Fast charging mode.
Q
I I P P NL NL S S DK DK N N FIN GR HU FIN GR HU CZ RU CZ RU
English
Green LED on = Fully charged battery pack.
Q
No LED on = Defective charger or battery pack.
Q
CHARGING YOUR BATTERY PACK
The battery pack for this unit has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it prior to use.
NOTE: Batteries will not reach full charge the first time
they are charged. Allow several cycles (trimming followed
by recharging) for them to fully charge.
TO CHARGE
Charge battery pack only with the charger provided.
Q
Make sure power supply is normal household
Q
voltage, 230 volts, 50 Hz, AC only.
Connect charger to power supply.
Q
Place battery pack in charger. Align raised rib on
Q
battery pack with groove in charger.
When charger is properly connected, red light will
Q
turn on. Press down on battery pack to be sure
contacts on battery pack engage properly with
contacts in charger.
Normally, the yellow and green lights on the charger
Q
will come on. This indicates charger is in control
charge mode and should switch to fast charge mode
within 5 minutes. When charger is in fast charge
mode the yellow and green lights will go off and the
red light will come on.
If after a period of 15 minutes the yellow and green
lights remain on, remove the battery pack, wait
1 minute and reinsert battery pack in charger. If the
yellow and green lights continue to remain on an
additional 15 minutes, the battery pack is damaged
and will not accept charge.
When your battery pack becomes fully charged,
Q
the red light will turn off and the green light will
turn on. After normal usage, 1 hour of charge time
is required to be fully charged. A minimum charge
time of 1 to 1-1/ 2 hours is required to recharge a
completely discharged battery pack. The battery pack
will become slightly warm to the touch while charging.
This is normal and does not indicate a problem.
14
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT
CAUTION
To prevent damage to battery pack, remove
battery pack from charger immediately if no LED
comes on. Return battery pack and charger
to your nearest Authorised Service Centre for
checking or replacing. Also, if you are removing
battery pack from charger and no LEDs are on,
return both battery pack and charger to your
nearest Authorised Service Centre. Do not insert
another battery pack into charger. A damaged
charger may damage a battery pack.
LV LV SK BG SK BG