Specifications - Sony PVM-2551MD Instructions D'utilisation

Specifications

Picture performance
Panel OLED panel
Picture size (diagonal)
623.4 mm (24
Effective Picture size (H × V)
543.4 × 305.6 mm
1
(21 /
2
Resolution (H × V)
1920 × 1080 pixels (Full HD)
Aspect 16:9
Pixel efficiency 99.99%
Panel drive RGB 10-bit
Viewing angle (panel specification)
89°/89°/89°/89° (typical) (up/down/
left/right, contrast > 10:1)
Normal scan 0% scan
Over scan 20% over scan
Warm-up time Approx. 30 minutes
To provide stable picture quality, turn
on the power of the monitor and
leave it in this state for more than 30
minutes.
Input
Composite input (NTSC/PAL) connector
BNC type (×1)
1 Vp-p ± 3 dB sync negative
Y/C input connector
Mini-DIN 4-pin (×1)
Y: 1 Vp-p ± 3 dB sync negative
C: 0.286 Vp-p ± 3 dB (NTSC burst
signal level)
0.3 Vp-p ± 3 dB (PAL burst signal
level)
RGB/component input connectors
BNC type (×3)
RGB: 0.7 Vp-p ± 3 dB (Sync On
Green, 0.3 Vp-p sync negative)
Component: 0.7 Vp-p ± 3 dB (75%
chrominance standard color bar
signal)
External synchronized input connector
BNC type (×1)
0.3 Vp-p to 4.0 Vp-p ± bipolarity
ternary or negative polarity binary
HD15 input connector
D-sub 15-pin (×1)
R/G/B: 0.7 Vp-p, sync positive (Sync
On Green, 0.3 Vp-p sync negative)
Sync: TTL level (polarity free, H/V
separate sync)
Plug & Play function: corresponds to
DDC2B
5
/ inches)
8
1
× 12 / inches)
8
DVI-D input connector
DVI-D (×1)
TMDS single link
Parallel remote
Modular connector 8-pin (×1)
Serial remote (LAN)
D-sub 9-pin (RS-232C) (×1)
RJ-45 modular connector (×1)
(Ethernet, 10BASE-T/100BASE-
TX)
Optional input port
2 ports
Signal format:
H: 15 kHz to 45 kHz
V: 48 Hz to 60 Hz
DC IN connector
XLR-type 4-pin (male) (×1), DC 5V/
24V (output impedance 0.05 ohms
or less)
Output
Composite output connector
BNC type (×1)
Loop-through, with 75 ohms automatic
terminal function
Y/C output connector
Mini-DIN 4-pin (×1)
Loop-through, with 75 ohms automatic
terminal function
RGB/component output connectors
BNC type (×3)
Loop-through, with 75 ohms automatic
terminal function
External synchronized output connector
BNC type (×1)
Loop-through, with 75 ohms automatic
terminal function
General
Power OLED monitor (PVM-2551MD/
2551NB)
DC IN: 24 V 5.0 A 5 V 0.030 A
(Supplied from AC adaptor)
AC Adaptor (Sony, AC-110MD)
AC IN: 100 V-240 V, 50/60 Hz, 1.53 A-
0.58 A
DC OUT: 24 V 5.0 A 5 V 0.060 A
Power consumption
Approx. 135 W (max.)
Approx. 80 W (average power
consumption in the default status)
Operating conditions
Temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended temperature
20 °C to 30 °C (68 °F to 86 °F)
Humidity 30% to 85% (no condensation)
79
Specifications