Technical Data; Scope Of Supply; Applications - REMS Tiger ANC Notice D'utilisation

eng
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when used
with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small metal objects, that
can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
Safety instructions for REMS reciprocating saws
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
● Hold the power tool by the insulated handles ("A") when performing work
where the tool can come into contact with concealed electric cables or its
own power cable. Contact with a live cable can also put metal tools under voltage
and lead to electric shock.
● Hold the power tool tightly with both hands when working and make sure
you have a firm footing. The power tool can be controlled more safety with two
hands.
● Use personal safety equipment, e.g. protective glasses. Chips fly off to all
sides when sawing. Keep other persons away.
● Please note that health hazardous dusts could be produced when sawing.
Use suitable dust extractors, a respirator and disposable overalls if necessary.
Observe the national regulations.
● Use suitable finders to locate concealed supply lines or consult the local
supply company. Contact with electric cables can cause fires and electric shock.
Damage to a gas pipe can cause explosions. Penetration of a water pipe can
cause property damage or electric shock.
● Make sure when sawing pipes carrying water that no leaking water can get
into the motor. There is a danger of electric shock.
● Clamp the material tightly. Do not support the workpiece with your hand
or foot. There is a danger of injury.
● Secure the workpiece. It is safer to hold the workpiece with a clamping device
or vice than with your hand.
● Do not touch any objects or the ground with the running saw. There is a
danger of recoil.
● Keep your hands away from the sawing area. Do not reach underneath the
workpiece. Contact with the saw blade can cause injury
● Make sure that the support shoe is always resting on the workpiece when
sawing. The saw blade can jam and lead to loss of control over the power tool.
● When you have finished the work, switch off the power tool and do not
remove the saw blade from the cut until it has come to a standstill. This
avoids recoil and allows you to put down the power tool safely.
● Only use undamaged, flawless saw blades. Bent or blunt saw blades can
break or cause recoil.
● Do not slow down the saw blade after switching off by pressing against
the side. The saw blade could be damaged, break or cause recoil.
● Wait until the power tool has come to a standstill before you put it down.
The inserted tool can jam and lead to loss of control over the power tool.
● Pull out the mains plug or remove the battery before attaching/detaching
the saw blade. There is a danger of injury.
● Pull out the mains plug or remove the battery before adjusting the support
shoe. There is a danger of injury.
Explanation of symbols
DANGER
Danger with a high degree of risk which results in death or
severe injury (irreversible) if not heeded.
WARNING Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use eye protection
Use a respirator
Use ear protection
Electrical device complies with protection class II
Environmental friendly disposal
Force-transmitting
guide holder
90°
90°
Steel pipes
Metal
Stainless steel
Pallets
Wood
Wood with nails
Green wood

1. Technical data

Use for the intended purpose
WARNING
REMS reciprocating saws are intended, using suitable saw blades, for sawing many
materials, e.g. steel pipes, cast iron pipes, other metal profiles, wood, wood with
nails, pallets, building materials, plastics, also for plunge-cut sawing in material that
is not too hard.
All other uses are not for the intended purpose and are prohibited.

1.1. Scope of Supply

REMS Tiger ANC/VE/SR/pneumatic: Drive machine, Allen key, guide holder
up to 2", 2 REMS special saw blades up to 2"/140-3.2, sheet steel box, operating
instructions
REMS Puma VE: Drive machine, Allen key, 1 REMS saw blade 210-1.8/2.5,
sheet steel box, operating instructions
REMS Cat ANC VE: Drive machine, Allen key, 1 REMS universal saw blade
150-1.8/2.5, sheet steel box, operating instructions
REMS Akku-Cat ANC VE: Drive machine, battery, rapid charger, Allen key, 1
REMS universal saw blade 150-1.8/2.5, sheet steel box, operating instructions
1.2. Article numbers
REMS Tiger ANC drive unit
REMS Tiger ANC VE drive unit
REMS Tiger ANC SR drive unit
REMS Tiger ANC pneumatic drive unit
REMS Puma VE drive unit
REMS Cat ANC VE drive unit
REMS Akku-Cat ANC VE drive unit Li-Ion
Battery Li-Ion 18 V, 2,6 Ah
Battery Li-Ion 18 V, 3,5 Ah
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W

1.3. Applications

Right-angled sawing with REMS Tiger ANC/VE/SR/pneumatic:
With guide holder 563000 and
REMS special saw blade 561001, 561007
Pipes (also plastic jacketed)
With guide holder 563100 and
REMS special saw blade 561002
Pipes (also plastic jacketed)
eng
Breeze blocks
Plaster boards
Pumice, brick
Cast iron
corrugated
straight-set
straight
pellets
560000
560008
560001
560002
560003
560004
560009
565215
565218
571560
up to 2"
up to 4"