Technical Data; Preparations For Use - REMS Tiger ANC Notice D'utilisation

eng
Explanation of symbols
Read the operating manual before starting
Environmental friendly disposal
Power tool corresponds to protection class I
Power tool corresponds to protection class II

1. Technical Data

1.1. Article numbers
REMS Tiger ANC drive unit
REMS Tiger ANC VE drive unit
REMS Tiger ANC SR drive unit
REMS Tiger ANC pneumatic drive unit
REMS Panther ANC VE drive unit
REMS Cat ANC VE drive unit
REMS Akku-Cat ANC VE drive unit Li-Ion
REMS High-Power-Battery Li-Ion 18 V
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
1.2. Capacities
Square sawing
REMS Tiger ANC, REMS Tiger ANC VE, REMS Tiger ANC SR,
REMS Tiger ANC pneumatic
With guide support 563000 and
REMS special saw blade 561001
Pipes (including plastic coated)
Metal, wood, plaster, etc.
With guide support 563100 and
REMS special saw blade 561002
Pipes (including plastic coated)
Metal, wood, plaster, etc.
REMS Tiger ANC SR with guide support
and REMS universal saw blade
Stainless steel pipes (INOX)
Metal, wood, plastic
Hand-held sawing
all REMS reciprocating saws
REMS universal saw blades and
REMS saw blades (see 2.4.)
Steel pipes and others
Other metal profiles,
Nail-embedded wood,
pallets
1.3. Number of strokes (idling speed)
REMS Tiger ANC
REMS Tiger ANC VE (infinitely variable)
REMS Tiger ANC SR (infinitely variable)
REMS Tiger ANC 48 V
REMS Tiger ANC pneumatic
REMS Panther ANC VE (infinitely variable)
REMS Cat ANC VE (infinitely variable)
REMS Akku-Cat ANC VE (infinitely variable)
1.4. Electric data
REMS Tiger ANC, REMS Tiger ANC VE,
REMS Cat ANC VE 230 V; 50 – 60 Hz; 1050 W; 5 A or
110 V; 50 – 60 Hz; 1050 W; 10 A or
48 V; 750 W; 16.5 A
all-insulated (73/23/EWG)
interference-suppressed (89/336/EWG)
REMS Tiger ANC SR 230 V; 50 – 60 Hz; 1400 W; 6.4 A or
110 V; 50 – 60 Hz; 1400 W; 12.8 A
all-insulated (73/23/EWG)
interference-suppressed (89/336/EWG)
REMS Panther ANC VE 230 V; 50 – 60 Hz; 500 W; 2.3 A or
110 V; 50 – 60 Hz; 500 W; 4.6 A
all-insulated (73/23/EWG)
interference-suppressed (89/336/EWG)
REMS Akku-Cat ANC VE 18 V=; 2.0 Ah; 30 A
Rapid-charger Input
Li-Ion/Ni-Cd (1 h) Output
1.5. Compressed-air supply REMS Tiger ANC pneumatic
Required working pressure
Air consumption at idling speed
Air consumption at full speed
Tube width
Oiler adjustment
560000
560008
560001
560002
560005
560004
560009
565215
571560
up to 2"
3 mm and thicker
up to 4"
3 mm and thicker
up to 2" or 4"
1.5 mm and thicker
Ø ≤ 6", 160 mm
≤ 250 mm
2200 rpm
0 ... 2200 rpm
700 ... 2200 rpm
1300 rpm
1800 rpm
0 ... 2200 rpm
0 ... 2200 rpm
0 ... 1700 rpm
230 V~; 50 – 60 Hz; 65 W
12 – 18 V=
6 bar (85 psi)
1.6 m³/min (56 cf/min)
1.3 m³/min (46 cf/min)
12 – 13 mm (½")
6 – 7 drops/min
1.6. Dimensions
REMS Tiger ANC
REMS Tiger ANC VE
REMS Tiger ANC SR
REMS Tiger ANC pneumatic
REMS Panther ANC VE
REMS Cat ANC VE
REMS Akku-Cat ANC VE
1.7. Weights
REMS Tiger ANC
REMS Tiger ANC VE
REMS Tiger ANC SR
REMS Tiger ANC pneumatic
REMS Panther ANC VE
REMS Cat ANC VE
REMS Akku-Cat ANC VE (with battery)
REMS High-Power-Battery 18 V
REMS Guide support up to 2"
REMS Guide support 2½ – 4"
1.8. Noise information
Sound pressure level
all REMS reciprocating saws
Sound capacity level
all REMS reciprocating saws
Uncertainty K = 3 dB
1.9. Vibrations
Weighted effective value of acceleration:
all REMS reciprocating saws
Sawing chipboard 18.3 m/s²
Sawing wooden beam 28.3 m/s²
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
Attention: The indicated weighted effective value of acceleration can differ
during operation from the indicated value, dependent on the manner in which
the device is used. Dependent upon the actual conditions of use (periodic duty)
it may be necessary to establish safety precautions for the protection of the
operator.

2. Preparations for Use

2.1. Electrical connection
Ensure correct mains voltage! Before connecting the drive unit respectively the
rapid charger, check whether voltage on the rating plate matches the mains
voltage. At work sites, in damp surroundings or in case of comparable type of
use, only operate the equipment off the mains using a 30 mA fault current
protected switch (FI breaker).
The battery supplied with REMS Akku-Cat ANC VE as well as spare batteries
are not charged. Charge battery before initial operation. Use only REMS rapid-
charger (571560) for charging. The rechargeable batteries only reach their full
capacity after being charged several times. Li-ion batteries should be recharged
regularly in order to avoid their total discharge. The rechargeable battery will
be damaged by exhaustive discharge. Non-rechargeable batteries may not be
charged.
NOTICE
Always hold the rechargeable battery upright when inserting it in the drive unit
or the rapid charger. If inserted at an angle it can cause damage to the contacts
and result in a short circuit which damages the battery.
Rapid charger Li-ion/NiCd (Art. No. 571560)
The left control lamp lights up and remains green when the mains plug is
plugged in. If a battery is inserted in the rapid charger, the green control lamp
flashes to indicate that the battery is charging. The green light stops flashing
and remains on to signal that the battery is fully charged. If the red control lamp
flashes, the battery is defective. If the red control lamp comes on and remains
on, this indicates that the temperature of the rapid charger and / or the recharge-
able battery is outside the permissible range of +5°C to +40°C.
NOTICE
The rapid chargers are not suitable for outdoor use.
2.2. Sawing with guide support (square cutting)
Insert mounting pin (3) of the guide support (2) sideways into the saw so that
the stop pin of the guide support will move in the slot of the machine.
CAUTION
To obtain square cuts, the use of the REMS guide support is indispensable.
Precise positioning is not possible when saw is guided by hand.
2.3. Free hand sawing
The reciprocating saw is used without the guide support (2). It must be pressed
forcefully against the material during sawing, in a way that the support shoe
(6) touches the material at any time.
eng
455×80× 90 mm (17.9"×3.2"×3.5")
435×80×135 mm (17.1"×3.2"×5.3")
490×80× 90 mm (19.3"×3.2"×3.5")
445×80× 90 mm (17.5"×3.2"×3.5")
320×80×110 mm (12.6"×3.2"×4.3")
435×80×135 mm (17.1"×3.2"×5.3")
435×90×190 mm (17.1"×3.5"×7.5")
3.0 kg (6.6 lb)
3.0 kg (6.6 lb)
3.1 kg (6.8 lb)
3.8 kg (8.4 lb)
2.4 kg (5.3 lb)
3.0 kg (6.6 lb)
3.5 kg (7.7 lb)
1.0 kg (2.2 lb)
1.0 kg (2.2 lb)
1.7 kg (3.7 lb)
96 dB(A)
107 dB(A)
K = 3.3 m/s²
K = 2.4 m/s²