Specific Safety Instructions; Technical Data - REMS Turbo K Notice D'utilisation

eng
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust related hazards.
h) Only allow trained personnel to use the power tool. Apprentices may
only operate the power tool when they are over 16, when this is necessary
for their training and when they are supervised by a trained operative.
D) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to ope-
rate the power tool. Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired by
a qualified expert or by an authorised REMS after-sales service faci-
lity before use. Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece. This
is safer than holding it with your hand, and also it frees both hands to
operate the equipment.
h) Use the power tool, accessories and tool bits etc., in accordance
with these instructions and in the manner intended for the particular
type of power tool, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation. All unauthori-
sed modifications to the power tool are prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery
pack. Inserting the battery pack into power tools that have the switch on
invites accidents.
b) Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery may create a risk of fire
when used with another battery pack.
c) Use battery tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal
objects like paper clips, coins, keys, nails, screws, or other small
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery,
avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of 5°C/40°F or 40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste.
Take them to an authorised REMS after-sales service facility or to a
reputed waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
b) Comply with maintenance instructions and instructions on tool re-
placements.
c) Check mains lead of power tool regularly and have it replaced by a
qualified expert or an authorised REMS after-sales service facility in
case of damage. Check extension cable regularly and replace it
when damaged.

Specific Safety Instructions

• Do not overload the sawblade and saw. Do not use damaged sawbla-
des. Do not apply excessive feed pressure.
• Attention! Cut parts become warm.
• Machine not suited for dust generating jobs.
• Wear ear protectors.
• Never operate the saw without its safety cover.
• Wear cloves when touching saw blades and rigid materials (saw blades
must be carried in a box whenever practicable).
• Failures of the machine, including the protection devices or saw blade,
must be reported to the responsible person for safety whenever disco-
vered.
• The floor in the vicinity of the machine must be even, clean and free
from loose particles, e.g. chips and cutting waste.
• Do not remove cutting waste or other material from the cutting area as
long as the machine is running and the sawing aggregate still in motion.
• REMS cooling lubricants in spray cans (REMS Spezial, REMS Sanitol)
are environment-friendly but contain combustible propellant (butane).
Spray cans are pressurized-do not force open. Also, protect them from
exposure to strong sunlight and heating above 50°C.
• Due to the degreasing effect of the cooling lubricants (thread-cutting
oils), an intensive skin contact has to be avoided. An appropriate skin
protector has to be applied.
• Due to hygienical reasons the trough has to be cleaned regularly from
dirt and chips, at least, however, once a year.
• It is not required to check the cooling lubricant because, due to the con-
sumption, new cooling lubricant is refilled from time to time.
• Do not allow undiluted cooling lubricant to get into drainage, water
systems or the soil. Remaining cooling lubricants have to be delivered
to specialized waste disposal companies. Disposal identity number for
mineral-based cooling lubricants 54401, for synthetic 54109.

1. Technical data

1.1. Article numbers
REMS Turbo K with automatic cooling lubricant unit
REMS Turbo Cu-INOX circular pipe saw
for dry-sawing
REMS universal circular metal saw blade
HSS, 225x2x32, 120 teeth
REMS circular metal saw blade
HSS especially for stainless steel pipes,
fine toothing, 225x2x32, 220 teeth
REMS circular metal saw blade HSS-E (cobalt alloyed),
especially for stainless steel pipes, fine toothing,
225x2x32, 220 teeth. Very long life.
Ring spanner WAF 27/17
Allen-key
REMS Herkules stock support
1.2.1. Working range REMS Turbo K
Sawblade
Max. cutting depth
Cross-sections: pipe, section, solid
Materials: steel, stainless steel, non-ferrous
metal, light metal, plastic etc. up to a
strength of approx. 1000 N/mm²
Right-angled cuts and bevel cuts up to 45°
)
<
90° ±
78 55 70×50
45° ²
60 55 60×40
eng
849007
849006
849700
849703
849706
849112
074005
120100
Ø 225 mm
78 mm
50×50 40 40 50×30
50×50 40 40 50×30