Required For Completion; Optional Parts; Required Tools And Adhesives; Optional Tools And Adhesives - Horizon Hobby HANGAR 9 P-47 Thunderbolt PNP Manuel D'utilisation

REQUIRED FOR COMPLETION

# Required Part #
2 SPMA3050 Standard Servo Extension 3-inch
1 SPMAR637T AR637T 6CH SAFE and AS3X Telemetry Receiver
1 SPMR6775 NX6 6 Ch Transmitter Only
1 SPMX50004S30 5000mAh 4S 14.8V Smart LiPo 30C IC5

OPTIONAL PARTS

# Required Part #
1 APC14012E Electric Propeller,14 X 12E
1 SPMX40004S30 4000mAh 4S 14.8V Smart 30C; IC3
1 SPMAR8360T AR8360T 8CH SAFE Telemetry RX
1 SPMR10100 NX10 10-Ch Transmitter Only
1 SPMR8200 NX8 8-Ch DSMX Transmitter Only
HIGH POWER
# Required Part #
1 APC12080E Thin Electric Prop, 12 x 8E
1 SPMX50006S30 5000mAh 6S 22.2V Smart 30C; IC5
OPTIONAL BATTERIES FOR HIGH POWER (WHEN USING 12 X 8 PROPELLER)
# Required Part #
1 SPMX40006S30 4000mAh 6S 22.2V Smart 30C; IC5
1 SPMX40006S50 4000mAh 6S 22.2V Smart 50C; IC5
1 SPMX46S50 4000mAh 6S 22.2V Smart G2 50C;
1 SPMX50006S50 5000mAh 6S 22.2V Smart 50C; IC5
1 SPMX56S30 5000mAh 6S 22.2V Smart G2 30C;
1 SPMX56S50 5000mAh 6S 22.2V Smart G2 50C;

REQUIRED TOOLS AND ADHESIVES

Balancing stand
Flat-blade screwdriver
Hex wrench: 1.5mm
Nut driver: 1/4-inch
Phillips screwdriver: #1 and #2
Square
EN
Description
Description
Description
Description
Description

OPTIONAL TOOLS AND ADHESIVES

30-minute epoxy
Epoxy brush
Felt-tipped pen
Hobby knife with #11 blade
Low-tack tape
Mixing cups
Mixing sticks
Thin CA

BATTERY AND OPTIONAL PROPELLER SELECTION

We recommend a 5000mAh 4S 14.8V battery for the Hangar 9
propeller when using a 5000mAh 4S 14.8V battery. The motor and speed controller can also be used with 5S or 6S
batteries if the propeller is changed to the optional 12 x 8E propeller.
Testing has shown the airframe is capable of handling the additional power. For more aggressive aerobatics it is
recommend to glue the wing halves together. It is also recommended to glue the fin and stabilizer to the fuselage to
increase their strength.

BUILDING PRECAUTIONS

During assembly, we recommend resting the parts on a soft surface such as a soft towel to help prevent denting the
sheeting.

REMOVING WRINKLES

The covering of your model may develop wrinkles during shipping and will require the use of a heat gun (HAN100)
and covering glove (HAN150) or covering iron (HAN101) with a sealing iron sock (HAN141) to remove them. Use
caution while working around areas where the colors overlap to prevent separating the colors. Avoid using too much
heat, which could separate the colors. Placing a cool damp cloth on adjacent colors will also help in preventing the
separation of the colors while removing wrinkles.
4
Description
P-47 Thunderbolt. Use the included 14 x 12 wood
®