Reflex omat RSC Smart AT8300A Mode D'emploi Original page 20

Information concerning the operating instructions
1 Information concerning the operating instructions
These operating instructions are an important aid for ensuring the safe and reliable
functioning of the device.
Reflex Winkelmann GmbH accepts no liability for any damage resulting from
failure to observe the information in these operating instructions. In addition to the
requirements set out in these operating instructions, national statutory regulations
and provisions in the country of installation must also be complied with (concerning
accident prevention, environment protection, safe and professional work practices,
etc.).
These operating instructions describe the device with basic equipment and
interfaces for optional equipment and accessories with additional functions.
 Note!
Every person installing this equipment or performing any other work at the
equipment is required to carefully read this manual prior to commencing
work and to comply with its instructions. The manual is to be provided to
the device operator and must be stored near the device for access at any
time.
2 Liability and guarantee
The device has been built according to the state of the art and recognised safety
rules. Nevertheless, its use can pose a risk to life and limb of personnel or third
persons as well as cause damage to the system or other property.
It is not permitted to make any modifications at the device, such as to the
hydraulics or the circuitry.
The manufacturer shall not be liable nor shall any warranty be honoured if the
cause of any claim results from one or more of the following causes:
• Improper use of the device.
• Unprofessional commissioning, operation, service, maintenance, repair or
installation of the device.
• Failure to observe the safety information in these operating instructions.
• Operation of the device with defective or improperly installed
safety/protective equipment.
• Failure to perform maintenance and inspection work according to schedule.
• Use of unapproved spare parts or accessories.
Prerequisite for any warranty claims is the professional installation and
commissioning of the device.
 Note!
Arrange for Reflex Factory Customer Service to carry out commissioning
and annual maintenance,  13.1 "Reflex Customer Service",  33.
3 Safety
3.1 Explanation of symbols
The following symbols and signal words are used in these operating instructions.
Danger of death and/or serious damage to
DANGER
health
The sign, in combination with the signal word
"Danger", indicates imminent danger; failure to
observe the safety information will result in
death or severe (irreversible) injuries.
Serious damage to health
WARNING
The sign, in combination with the signal word
"Warning", indicates imminent danger; failure to
observe the safety information can result in
death or severe (irreversible) injuries.
Damage to health
CAUTION
The sign, in combination with the signal word
"Caution", indicates danger; failure to observe
the safety information can result in minor
(reversible) injuries.
Damage to property
ATTENTION
The sign, in combination with the signal word
"Attention", indicates a situation where damage
to the product itself or objects within its vicinity
can occur.
20 — English

Note!
3.2 Personnel requirements
Installation and operation tasks are to be carried out by specialist personnel or
specially trained personnel only.
The electric connections and the wiring of the device must be executed by a
trained electrician in accordance with all applicable national and local regulations.
3.3 Personal protective equipment
Use the prescribed personal protective equipment as required (e.g. ear protection,
eye protection, safety shoes, helmet, protective clothing, protective gloves) when
working on the system.
Information on personal protective equipment requirements is set out in the
relevant national regulations of the respective country of operation.
3.4 Intended use
The device is a pressure maintaining station for heating and cooling water
systems. It is used to maintain the water pressure and to add water within a
system. The devices may be used only in systems that are sealed against
corrosion and with the following water types:
• Non-corrosive
• Chemically non-aggressive
• Non-toxic
The ingress of atmospheric oxygen by permeation into the entire heating and
cooling water system, make-up water and similar must be reliably minimized
during operation.
3.5 Impermissible operating conditions
The device is not suitable for the following applications:
• Mobile system operation.
• Outdoor operation.
• For use with mineral oils.
• For use with flammable media.
• For use with distilled water.
 Note!
It is not permitted to make any modifications to the hydraulic system or
the circuitry.
3.6 Residual risks
The device has been manufactured using state-of-the-art technology. Despite this,
residual risks always remain.
WARNING
Risk of fire due to open ignition sources
The device housing is made of combustible material and is heat-sensitive.
• Avoid heat and ignition sources (flames or sparks).
WARNING
Risk of injury due to heavy weight
The devices are heavy. Consequently, there is a risk of physical injury and
accidents.
• Use suitable lifting equipment for transportation and installation.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
• Wear protective gloves.
• Please place appropriate warning signs in the vicinity of the device.
Reflexomat RSC Smart — 21.10.2025-Rev. C
This symbol, in combination with the signal
word 'Note', indicates useful tips and
recommendations for efficient handling of the
product.