Noise Information; Items Included - Bosch GCM 8 SJL Professional Notice Originale

28 | English
Sliding mitre saw
mW
Laser class
Divergence of mrad
laser line (full
angle)
Weight according kg
to EPTA-Proced-
ure 01:2014
Protection class
Dimensions of suitable saw blades
Saw blade dia- mm
meter
Base blade thick- mm
ness
Max. cutting width mm
Hole diameter mm
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Permissible workpiece dimensions (see "Permissible workpiece dimensions", page 31)

Noise Information

Noise emission values determined according to
EN 62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 99 dB(A); sound power level
112 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
1 609 92A 5U7 | (14.09.2020)
GCM 8 SJL GCM 8 SJL
< 0.39 < 0.39
1M 1M
1.0 1.0
17.3 17.3
/ II / II
216 216
1.3−1.8 1.3−1.8
3.3 3.3
30 30

Items included

Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with mounted saw blade
– Screw clamp (28)
– Hex key (33)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Stationary or flexible mounting
u
Mounting on a work surface (see figure a1−a2)
– Use suitable screw fasteners to secure the power tool to
or
– Firmly clamp the base of the power tool to the work sur-
GCM 8 SJL GCM 8 SJL
< 0.39 < 0.39
1M 1M
1.0 1.0
17.3 17.3
/ II
216 216
1.3−1.8 1.3−1.8
3.3 3.3
25.4 25.4
See the list of items included at the start of
the operating manual.
To ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use.
the work surface. The holes (26) are used for this pur-
pose.
face with commercially available screw clamps.
GCM 8 SJL
< 0.39
1M
1.0
17.3
/ II / II
216
1.3−1.8
3.3
25.4
Bosch Power Tools