Technical Data; Noise/Vibration Information - Bosch GDC 125 Professional Notice Originale

OBJ_BUCH-1810-003.book Page 16 Tuesday, June 4, 2013 1:05 PM
16 | English

Technical Data

Marble Cutter
Article number
Rated power input
Rated speed
Max. diameter for diamond cutting
discs
Cutting discs width, min.
Cutting discs width, max.
Mounting bore
Max. cutting depth for 0° bevel
angle with diameter of diamond
cutting disc
– 125 mm
Max. cutting depth for 45° bevel
angle with diameter of diamond
cutting disc
– 125 mm
Dimensions of base plate
Bevel-angle adjustment to 45°
Spindle lock
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =4.0 m/s , K=1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
1 609 92A 0CV | (4.6.13)
Declaration of Conformity
We declare under our sole responsibility that the product de-
GDC 125
scribed under "Technical Data" is in conformity with the fol-
3 601 E48 0..
lowing standards or standardization documents: EN 60745
1300
according to the provisions of the directives 2011/65/EU,
-1
2004/108/EC, 2006/42/EC.
min 12000
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9
mm 125
D-70745 Leinfelden-Echterdingen
mm 1.6
Henk Becker
mm 2.2
Executive Vice President
mm 22.23
Engineering
mm 40.0
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
03.06.2013
Assembly
mm 26.5
mm 101.3 x 179
 Before any work on the machine itself, pull the mains

plug.

Dust Extraction
 Dusts from materials such as lead-containing coatings,
kg 2.7
some wood types, minerals and metal can be harmful to
/I
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Mounting/Replacing the Diamond Cutting Disc
(see figure A)
 When mounting and replacing diamond cutting discs, it
is recommended to wear protective gloves.
 Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
 Always use a correctly sized diamond cutting disc with
the fitting mounting hole that corresponds with the in-
formation listed in the technical data.
 Use only diamond-tipped cutting discs. Segmented dia-
mond wheels may only have negative cutting angles and
slots between the segments to a maximum of 10 mm.
Mounting the Diamond Cutting Disc
– Clean the diamond cutting disc 19 and all clamping parts
to be mounted.
– Mount the mounting flange 18 onto the drive spindle 17.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools