Technical Data; Charging The Battery - Bosch GKM 18V-50 Professional Notice Originale

(1) Spindle lock button
(2) Protective guard with chip container
(3) Utility hook
(4) Cutting depth scale
(5) Hex key
(6) Lock-off function for on/off switch
(7) On/off switch
a)
(8) Battery release button
a)
(9) Battery
(10) Clamping lever for cutting depth preselection
(11) Motor housing
(12) 0° cut mark
(13) Base plate
a)
(14) Parallel guide
(15) Handle (insulated gripping surface)
(16) Clamping bolt with washer
(17) Clamping flange
a)
(18) Circular saw blade
(19) Mounting flange
(20) Saw spindle
(21) Retracting blade guard
(22) Adjusting lever for retracting blade guard
a)
(23) Pair of screw clamps
(24) Lid of the chip container
(25) Chip container locking mechanism
(26) "PowerLight" lamp
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Hand-held circular saw
Article number
Rated voltage
A)
No-load speed
B)
Max. cutting depth
– at a 0° mitre/bevel angle
Spindle lock
Base plate dimensions
Max. saw blade diameter
Max. base blade thickness
Min. base blade thickness
Max. tooth thickness/offset
Min. tooth thickness/offset
Locating bore
Weight according to
EPTA-Procedure 01:2014
Bosch Power Tools
Hand-held circular saw
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20–25 °C with rechargeable battery GBA 18V
B) If the ProCore 18V 12.0Ah battery is used, this sits on the work-
C) Limited performance at temperatures < 0 °C
Fitting
u

Charging the Battery

u
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
GKM 18V-50
protective circuit: The application tool no longer rotates.
3 601 FB8 0..
u
V 18
-1
min 4250
Follow the instructions on correct disposal.
Removing the battery
mm 50
The battery (9) is equipped with two locking levels to pre-
●
vent the battery from falling out if the battery release button
mm 105 x 200
(8) is pressed unintentionally. As long as the battery is inser-
mm 136
ted in the power tool, it is held in position by means of a
spring.
mm 1.6
To remove the battery (9), press the release button (8) and
mm 1.0
pull the battery to the rear and out of the power tool. Do not
mm 2.5
use force to do this.
mm 1.2
Battery charge indicator
mm 20
The green LEDs on the battery charge indicator indicate the
kg 2.6–3.6
state of charge of the battery. For safety reasons, it is only
C)
and
5.0Ah.
piece during working. Consequently, the maximum cutting
depth cannot be reached.
Only use saw blades the maximum permitted speed of
which is higher than the no-load speed of the power
tool.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
1 609 92A 74W | (10.03.2022)
English | 9
GKM 18V-50
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...