Elem Garden Technic CBT2538 Traduction Des Instructions D'origine page 14

cutting head. A broken or unbalanced nylon cutting head must never be used.
FOLLOW INSTRUCTION FOR CHANGING ACCESSORIES.
● Do not store in a closed area where fuel vapors can reach an open flame from hot water heaters, furnaces, etc. Store in a
locked, well ventilated area only.
● Ensure safe and proper performance of your product. These part are available from your dealer. The use of any other
accessories or attachments may cause a potential hazard or injury to the user, damage to the machine and void this
warranty.
● Clean the machine completely, especially, the fuel tank, its surroundings, and the air cleaner.
● When refueling, be sure to stop the engine and confirm that it is cooled down.. Never refuel when the engine is running or
hot. When gasoline spills, be sure to wipe it up completely dispose of those materials before starting the engine.
● Stay clear of other workers or bystanders by at least 15 meters/50 feet.
● When ever approaching an operator of the machine, carefully call his attention and confirm that the operator stop the
engine. Be careful not to startle or distract the operator which can cause an unsafe situation.
● Never touch the nylon cutting head when ever the engine is running. If it is necessary to adjust the protector or nylon
cutting head, be sure to stop the engine and confirm that the nylon cutting head has stopped running.
● The engine should be turned off when the machine is moved between work areas.
● Be careful not to hit the nylon cutting head against stones, or the ground.
Unreasonable rough operation will shorten the life of the machine as well as create an unsafe environment for yourself and
those around you.
● Pay attention to loosening and overheating of parts. If there is any abnormality of the machine, stop operation
immediately and check the machine carefully. If necessary, have the machine serviced by a authorized dealer. Never
continue to operate a machine which may be malfunctioning.
● In start-up or during operation of the engine, never touch hot parts such as the muffler, the high voltage wire or the
spark plug.
● After the engine has stopped, the muffler is still hot. Never place the machine in any places where there are
flammable materials (dry grass, etc.), combustible gasses or combustible liquids.
● Pay special attention to operation in the rain or just after the rain as the ground may be slippery.
● If you slip or fall to the ground or into a hole, release the throttle lever immediately.
● Be careful not to drop the machine or hit it against obstacles.
● Before proceeding to adjust or repair the machine, be sure to stop the engine and detach the spark plug.
● When the machine is placed in storage for a long time, drain fuel from the fuel tank and carburetor, clean the parts,
move the machine to a safe place and confirm that the engine is cooled down.
● Make periodic inspections to assure safe and efficient operation. For a thorough inspection of your machine, please
contact a dealer.
● Keep the machine away from fire or sparks.
● It is believed that a condition called Raynaud's phenomenon, which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. loss of color and numbness in the fingers. The following precautions
are strongly recommended because the minimum exposure which might trigger the ailment is unknown.
Keep your body warm, especially the head, neck, feet, ankles, hands and wrists.
Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not
smoking.
Limit the hours of operation. Try to fill each day with jobs where operating the brush cutter or other hand-held power
equipment is not required.
If you experience discomfort, redness and swelling of the fingers followed by whitening and loss of feeling, consult your
physician before further exposing yourself to cold and vibration.
● Always wear ear protection, loud noise for long time can make hearing debase even lost hearing.
● Total face and head protection must be wear to prevent damage from plummet or branch.
● Wear no-slip heavy duty work gloves to improve your grip on the brush cutter handle. Gloves also reduce the
transmission of machine vibration to your hands.
● WARNING: The cutter area is still dangerous while the machine is coasting to a stop.
27
DESCRIPTION
SAFETY MANUAL included with unit. Read before operating and keep for future reference to learn proper, safe
operating techniques.
1. NYLON CUTTER HEAD Contains replaceable nylon trimming line that advances when the trimmer head is
tapped against the ground while the head is turning at normal operating speed.
2. CUT-OFF KNIFE Trims nylon filament to the correct length-7‫ ,״‬head to end of line-when nylon trimming head is
bumped on the ground during operation, line advance. If trimmer is operated without a cut-off knife the line
becomes too long (more than7") the engine, this will overheat or damage the engine.
3. DEBRIS SHIELD Mounted just above the cutting attachment. Helps protest operator by deflecting debris
produced during debris produced during the trimming operation. Do not operate unit without shield.
4. D-HANDLE this handle can be adjust-ed at you convenience for comfort.
5. DRIVE SHAFT ASSEMBLY Contains a specially designed liner flexible drive shaft.
6. IGNITION SWITCH "slide switch" mounted on top of the Throttle Trigger Housing. Move switch FORWARD to
Run, BACK TO STOP.
7. SAFETY LEVER Before acceleration, compress it please.
8. THROTTLE TRIGGER Spring loaded to return to idle when released. When accelerating, press trigger gradually
for best operating technique. Do not hold trigger while starting.
9. PURGE BULB Pushing purge bulb (7 to 10 times before starting),will remove all air and sale fuel from fuel
system and bring fresh fuel to the carburetor.
28