HIKOKI NT 1850DA Mode D'emploi page 16

English
(7) Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□ THE NAILER MUST NOT OPERATE.
(8) Set the nailing operation indicator blinking ON mode.
(CONTACT ACTUATION MECHANISM)
Push the nailing operation switch once, make sure that
the indicator is blinking Blue.
Separate the push lever from the workpiece, pull the
trigger.
Depress the push lever against the workpiece within
2 seconds.
□ THE NAILER MUST OPERATE.
(9) If no abnormal operation is observed, you may load nails
in the Nailer.
Drive nails into the workpiece that is the same type to be
used in the actual application.
□ THE NAILER MUST OPERATE PROPERLY.
4. Checking push lever operations
WARNING
Make sure the trigger is locked when not fi ring nails.
Always make sure the trigger is locked and the battery
removed from the power tool when checking push lever
operations.
Check to make sure the push lever slides smoothly when
operated.
Clean the sliding area on the push lever if it doesn't slide
smoothly.
5. Load nails
WARNING
When loading nails into Nailer,
1) remove battery from the nailer;
2) do not pull trigger;
3) do not depress push lever; and
4) keep nailer pointed downward.
(1) Lightly press the stop lever and gently pull out the
magazine cover. (See Fig. 9)
(2) Set nail strip into the magazine and keep the points of
nails in contact with Groove. (See Fig. 10)
NOTE
The nails shown in page 12 can be loaded onto the side
guide groove of the magazine without any adjustment.
Always keep the points of nails in contact with Groove.
Magazine
Side guide
groove
Nail
Groove
(3) Slide the nail strip into the blade guide. (See Fig. 11)
(4) Confi rm that nail strip is placed with side guide grooves
and Groove properly, then push the magazine cover
forward to be latched.
HOW TO USE THE NAILER
WARNING
○ NEVER point tool at yourself or others in work area.
○ Keep fi ngers AWAY from trigger when not driving nails to
○ Do not use the electrical cord if damaged. Have it
○ Choice of triggering method is important.
○ Before starting work, check the nailing operation
○ Never place your face, hands or feet near fi ring head
○ Do not drive nails on top of other nails or with Nailer at too
○ Do not drive nails into thin boards or near corners and
○ Never drive nails from both sides of a wall at the same
○ Never use Nailer which is defective or operating
○ Do not use Nailer as hammer.
○ Remove all remaining fasteners and battery from nailer
○ Remove battery from Nailer when:
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use SINGLE SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
○ SINGLE SEQUENTIAL ACTUATION MECHANISM:
○ CONTACT ACTUATION MECHANISM:
1. Nailing procedures
Gap
16
avoid accidental fi ring.
repaired immediately.
Please read and understand "1. Nailing procedures"
found below.
switching device.
This HiKOKI nailer includes a nailing operation switching
device.
Before starting work, make sure that the switching
device is properly set.
If the switching device is not set properly, the nailer will
not operate correctly.
when using.
steep of an angle; nails can ricochet and hurt someone.
edges of workpiece. Nails can be driven through or away
from workpiece and hit someone.
time. Nails can be driven into and through the wall and
hit a person on the opposite side.
abnormally.
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) attaching or removing the nose cap;
4) cleaning a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
1) loading nails;
2) turning the adjuster.
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
After nailing once, nailing will not be possible again until
the trigger is released and pressed again.
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They are:
1. Intermittent operation (Trigger fi re):
2. Continuous operation (Push lever fi re):