HIKOKI NT 1850DA Mode D'emploi page 14

English
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights up green. In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about 3 seconds
to confi rm that the battery being charged with charger
is taken out, wait for a minimum of 3 seconds before
reinserting it to continue charging. If the battery is
reinserted within 3 seconds, the battery may not be
properly charged.
○ If the pilot lamp does not blink in red (every second)
even though the charger cord is connected to the power,
it indicates that the protection circuit of the charger may
be activated.
Remove the cord or plug from the power and then
connect it again after 30 seconds or so. If this does
not cause the pilot lamp to blink in red (every second),
please take the charger to the HiKOKI Authorized
Service Center.
BEFORE USE
Action
Removing and inserting the
battery
Charging
Selecting accessories
1. How to operate operation panel
(1) Power switch ON (See Fig. 4)
Under the condition of "Power switch OFF", push and
hold on Power switch more than 1 second, then power
indicator lights in Green.
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power off ]
WARNING
(2) Power switch OFF (See Fig. 4)
(3) Select Nailing operation mode
(4) Remaining battery level
Status of indicator
NOTE
Figure Page
2 2
3 2
― 326
14
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned off . To
turn on again, press the power switch.
Never leave the Nailer with the power on. This could
result in an accident.
Under the condition of "Power switch ON", push Power
switch, then power indicator goes off .
Under the condition of "Power switch ON", functions
below are active.
(Single sequential actuation / Contact actuation)
After power switch turn ON, always set in Single
sequential actuation mode as initial. (Nailing operation
indicator light in blue.) (See Fig. 5)
To change nailing operation mode, push Nailing
operation switch once. Every pushing, mode will change
between "Single sequential" and "Contact". (See Fig. 6)
Lighting (Blue):
SINGLE SEQUENTIAL ACTUATION MECHANISM,
Blinking (Blue):
CONTACT ACTUATION MECHANISM
While power switch ON, the battery remaining level can
be checked by status of LED lamp as below.
LED do not light
LED (Red) blinks
LED (Red) lights
There are situations in which this product will not operate
when two LEDs are lit on the battery's remaining battery
indicator.
This is not a malfunction but a control feature that is
specifi c to this product. The tool will operate when the
battery is recharged.
The battery remaining
power is enough.
The battery remaining
power is nearly empty.
The battery remaining
power is empty.
Recharge the battery as
soon as possible.