Arktic 233900 v.02 Manuel De L'utilisateur page 10

233917 v.02:
GB
A3. Power Switch
B3. Power regulator
C3. LED light bar (Max 5W)
D3. Fan
E3. Temperature Controller
F3. Fan
G3. Starter
H3. Compressor
I3. Overload Protector
235836 v.02:
A4. Power Switch
B4. Power regulator
C4. LED light bar (Max 8W)
D4. Fan
E4. Temperature Controller
F4. Fan
G4. Capacitor
H4. Starter
I4. Compressor
J4. Overload Protector
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accesso-
ries. In case of incomplete or damaged delivery, please contact
the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
1. Place the appliance on a stable and level surface. Ensure
the appliance is properly levelled using a water spirit level
(not supplied).
2. Let the appliance rest in its intended position for about 2
hours before operating to prevent damages to the cooling
circuit through shaken refrigerant.
3. Make sure the appliance is on OFF stage of main switch.
Connect the appliance to suitable power supply and turn on
the appliance. The default status is "temperature measuring
status".
4. Let the appliance reach the set temperature before putting
the pre-cooled beverages (< 6 °C) to the appliance evenly with
sufficient surrounding spacings to ensure proper air circu-
lation.
5. Close the door properly to keep the best performance.
6. Simply disconnect to switch OFF the appliance. Disconnect
the appliance when not in use.
7. Wait at least 5 minutes before plug in again the after unplug
the appliance or power sudden break.
10
NOTE:
• If no button is pressed within 30 seconds under any setting
mode (except parameter recovery setting mode), the newly
set temperature will be stored automatically.
• The temperature setting ranges from 2°C to 10°C.
• The height of each shelf can be adjusted according to the
height of the items.
• Do not exceed the maximum shelf load stated in the "Techni-
cal specifications".
User menu
1. Under "temperature measuring status", press "Set button"
button 3s to enter user menu. Only two items could be se-
lected – "St" and "Po".
2. Press "Rst button" to return to the "temperature measuring
status".
Set temperature
1. In user menu, select "St" and press "Set button" to enter
the "temperature setting mode", press or to adjust the set
temperature.
2. Press "Set button" to confirm and return to user menu.
Auto / Manual defrosts
1. The appliance will start defrost process automatically for
every 6 hours. When "def" indicator is ON, the appliance is
under defrost process.
2. Under "temperature measuring status", press "Rst button"
for 3s to manually open or close of defrost.
NOTE: Water in the drain tray is evaporated automatically. If
the humidity of environment over 60%, check the drain tray and
throw it away once a day.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.