Ferm MSM1040 Traduction De La Notice Originale page 13

2. Tilt the saw by using the handle (2) until the
indicator (19) reads the desired position on the
scale for bevel angle (20);
3. Tighten the adjusting knob for bevel
adjustment (22).
Switching the machine on/off
Fig. A
• To start the machine, press and hold the lock-
off button (1) and press the on/off switch (3).
• To stop the machine, release the on/off switch
(3).
Making a cross cut
Fig. H, I
Follow these steps to cut perpendicular to the
grain of the wood:
1. Adjust the mitre angle to and the bevel angle to
0°;
2. Move the adjustable fence to the inner
position, towards the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure J.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a mitre cut
Fig. I, J
Follow these steps to make an angled cut to the
face of the wood:
1. Adjust the mitre angle to the desired position
and the bevel angle to 0°;
2. Move the adjustable fence to the inner
position, towards the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure I.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a bevel cut
Fig. K, L
Follow these steps to make an angled cut to the
edge of the wood:
1. Adjust the mitre angle to 0° and the bevel
angle to the desired position ;
2. Move the adjustable fence to the outer
position, away from the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure L.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece. Ensure the
workpiece clamp is placed on the right side;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
Making a compound cut
Fig. L, M
Follow these steps to make a combination of
mitre and bevel cut:
1. Adjust the mitre angle and the bevel angle to
the desired position ;
2. Move the adjustable fence to the outer
position, away from the blade. The maximum
distance between the adjustable fence (35) and
the saw blade (6) is 8mm, as shown on figure L.
Make sure the fence does not touch the blade.
3. Firmly clamp the workpiece. Ensure the
workpiece clamp is placed on the right side;
4. Turn on the machine. Make sure that the saw
blade has reached full speed;
5. Now bring the handle slowly downwards so
that the saw blade cuts through the piece of
work and passes through the slot in the table.
Do not put undue pressure on the saw, let the
machine do the work;
6. Bring the handle gently up again and switch it
off by letting go of the switch.
13