Antenna Installation; Manual Programming - BFT MOOVI 30 Instructions D'utilisation Et D'installation

ENGLISH
JP2
7-8 START or key selector input (N.O.) with trimmer TW=max.
OPEN input (N.O.) with trimmer TW=min.
7-9 STOP pushbutton (N.C.). If not used, leave the bridge con-
nected.
7-10 Photocell input or pneumatic edge (N.C.). If not used, leave
the bridge connected.
7-11 Opening limit switch (N.C.). If not used, leave the bridge
connected.
7-12 Closing limit switch (N.C.). If not used, leave the bridge con-
nected.
13-14 Output 24V~supply to photocells or other devices.
15-16 Output for gate-open warning light outputor alternatively 2nd
radio channel.
17-18 Antenna input for radio-receiver plug-in board (17 signal-18
braid).
JP3
19-20 PEDESTRIAN input (N.O.) with trimmer TW=max.
CLOSE input (N.O.) with trimmer TW=min.
JP4 Radio-receiver board connector, 1-2 channels.
Fig.7 shows a general wiring diagram.
9.1) LED (Fig.16)
The ALPHA-ALPHA BOM control units are provided with a series
of self-diagnosis LEDs which control all the functions.
DL1: Incorporated radio receiver LED
DL2: START (trimmer TW=max)-comes on with the START command
OPEN (trimmer TW=min)-comes on with the OPEN command
DL3: STOP - Stop - goes off when a start command is given.
DL4: PHOT - Photocell - goes off when the photocells are not aligned
or in the presence of obstacles.
DL5: SWO - Goes off when the opening limit switch is operated.
DL6: SWC - Goes off when the closing limit switch is operated.
9.2) DIP-FIX SELECTION (Fig.16)
DIP1)
TCA [ON] - Automatic closing time TCA.
ON: Activates automatic closing
OFF: Excludes automatic closing
DIP2)
FCH [ON] - Photocells.
ON: Photocells are only active in the closing phase.
OFF: Photocells are active both in the closing and opening phase.
DIP3)
BLI - Blocks impulses.
ON: START commands are not accepted during the opening pha-
se.
OFF: START commands are accepted during the opening phase.
DIP4)
3P/4P - 3 Steps/4 Steps
ON: Enables 3-step logic.
OFF: Enables 4-step logic.
DIP5)
CODE FIX – Fixed code.
ON: Activates incorporated receiver in fixed code mode.
OFF: Activates incorporated receiver in rolling-code mode.
DIP6)
RADIO LEARN - Radio transmitter programming
ON: This enables transmitter storage via radio:
1 – First press the hidden key (P1) and then the normal key (T1,
T2, T3 or T4) of a transmitter already memorised in standard
mode by means of the radio menu.
2 – Within 10s press the hidden key (P1) and the normal key
(T1, T2, T3 or T4) of a transmitter to be memorised.
The receiver exits the programming mode after 10s, other new
transmitters can be entered before the end of this time.
This mode does not require access to the control panel.
OFF: This disables transmitter storage via radio. The transmitters
are only memorised by means of manual programming.
18
- MOOVI 30-50 - ALPHA BOM Ver. 05
INSTALLATION MANUAL
DIP7)
SCA – Gate-open warning light or 2nd radio channel.
OFF: Activates relay output in Gate-open warning light mode.
ON: Activates relay output as 2nd radio channel.
DIP8)
FAST CLOSE
ON: Closes the gate after photocell disengagement, before waiting
for the end of the TCA set.
OFF: Command not entered.
9.3) TRIMMER ADJUSTMENT (Fig.16)
TCA (Dip-Fix TCA ON)
It is used to set the automatic closing time, after which the gate
closes automatically (adjustable from 0 to 90 sec.).
TW
Working time is fixed to 10s.
trimmer TW= min: inputs 7-8 and 19-20 are considered as OPEN
trimmer TW =max: inputs 7-8 and 19-20 are considered as START
9.4) ACCESSORIES
SS (fig.16).
Optional board signalling gate open. Operates only with electrical
limit switches.
10) INTEGRATED RECEIVER TECHNICAL SPECIFICATION
Receiver output channels:
- output channel 1, if activated, controls a START command.
- output channel 2, if activated, controls the excitation of the 2nd
radio channel relay for 1s.
Transmitter versions which can be used:
all Rolling Code transmitters compatible with

ANTENNA INSTALLATION

Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can interfere
with radio reception. In case of insufficient transmitter range, move
the antenna to a more suitable position.
11) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means
of the universal palmtop programmer which allows you to create
installations in the "collective receivers" mode, as well as manage
the complete installation database using the EEdbase software.

12) MANUAL PROGRAMMING

In the case of standard installations where no advanced functions
are required, it is possible to proceed to manual storage of the
transmitters
1) If you wish the transmitter T key to be memorised as Start, press
thSW1 button on the control unit, otherwise if you wish the transmitter
key to be memorise as second radio channel, press the SW2 button
on the control unit.
2) When the DL1 LED blinks, press the transmitter P1 hidden key,
and the DL1 LED will stay on permanently.
3) Press the key to be memorised on the transmitter, LED DL1 will
start blinking again.
4) To memorise another transmitter, repeat steps 2) and 3).
5) To exit the storage mode, wait until the LED is switched off com-
pletely.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL TO
THE FIRST MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns the
key code to the receiver; this code is necessary in order to carry out
subsequent cloning of the radio transmitters.
12.1) CONTROL UNIT MEMORY CANCELLATION
In order to cancel the control unit memory completely, simultaneously
and CLOSE inputs respectively.
and PEDESTRIAN inputs respectively.
.