22
3 = Delivering the same product following another selection: in this case use command 06 to assign the
same code number and price to the selections that contain the same product. Therefore if after a selection
the product is not delivered, the machine considers that the selection is empty and automatically searches
for a selection that has the same product code number and the same price and then deliveres the product
from this selection. When all the selections with the same product code number are empty then the machine
returns to one of the two preceding options depending on the setting of the single or multisale parameter.
To "reset" the selections when they are being reloaded simply open the main door of the machine and insert
the feed key so that "porta aperta / door open" is displayed.
There can not be selections with the same code number but a different price. When the machine is turned on
it carries out a control and signals any programming errors by displaying TEST 18 and the selection
identifiers.
If it is an executive payment system and there are more than 7 selections with the same code number which
are "reset" but not loaded (they remain physically empty), after the door is shut carry out a sale cycle for any
one of these empty selections.***
E
***At this point the machine offers the choice of whether or not to enable the empty option (1 enabled, 0
N
disabled). This option operates in the 0, 1 and 2 modes previously set; if enabled, when a product is not
G
delivered ("not read by the photocell") the selection is considered empty and therefore no longer accessible.
L
To "reset" the empty selections simply open the main door of the machine and insert the feed key so that
I
"door open" appears on the display.
S
Once the operating function has been selected the machine suggests the activation or non-activation of a
H
sound signal while waiting for the product to drop. Use any of the buttons on the keyboard except "B" to
select either the activation "BEEP-ON" or the deactivation "BEEP-OFF" of the sound signal, and once the
desired option is displayed, press "B" to memorise the option .
Command 58 Diagnostic level:
The command can be set at 0 or 1. If the command is set at 1, in the event the selected spiral does not
complete the whole rotation, that selection goes out of order. Whereas if the command is set at 0 - the
default value - it does not go out of order.
Command 59 Entering the code for sales counter display:
This command is used for storing a 6-character code composed from any combination of the "A" and "B"
keys. When the machine is in stand-by and this code is keyed in the value of the sales number counter
which cannot be reset (see Command 09) is displayed for approximately 6 seconds on the screen.
Example:
1. Programming mode, display shows .........................................................................................Command 00
2. Key in 59 + key "B", display shows ........................................................................................Code 000000
3. Key in "B", display shows ........................................................................................................Code _00000
4. Key in the desired combination of the characters "A" and "B" ............................................. Code ABBAB_
5. When the sixth character is entered the code is stored and the display shows ....................------ OK -------
N.B. If key "A" is selected in point 3, the main menu of the programme is called up and the code remains
unaltered. If a 0 is selected in point 4, the code is completely zeroed and the relevant function impossible to
activate.
Command 60 Erases the memory:
This command will display the message "Code 0000". All data stored in the memory of the machine will be
erased by typing in code 6203 and pressing the B button. This function must be used very carefully to avoid
the accidental loss of all data. Electronically the machine is as new. The message "memory cleared"
appears on the display. The procedure for erasing the memory is as follows:
1. Go into programming mode to display ................................................................................._Command 00_
2. Key in 60 and press the B button to display ............................................................................_Code 0000_
3. Key in 6203 and press the B button to display .................................................................._memory cleared
To exit the command press the "test" push button once.
FAS INTERNATIONAL S.p.A. Via Lago di Vico, 60 SCHIO (VI) – tel. +39 0445 502011 – fax +39 0445 502010 - e-mail: info@fas.it
To set the following option ONLY, enter the "programming mode" and when the
message "command 00" appears on the display press the "test" button again for a
further 3 seconds, after which the buzzer will sound again for a few seconds, and
access to the second level of the menu is obtained. The message "Command 00" will
appear again. To quit the programming mode press the "A" key .
Activation of this command cancels all the data programmed by the user and
the new default parameters determined by the manufacturer are automatically
Spirali HDR Panzer - Issue 00