English - Enerpac ZU4 Instructions

6.5 G "Main" Menu (Ft-lb or Nm selected)
If Automode is
(see Screens 7A and 7B)
ON, and a unit of torque has been
selected, the screen text will alternate
between the selected torque wrench
model and "AUTO". Refer to QRC
step #4B.
(See Screens 7A and 7C) If Automode
is OFF, the screen text will alternate
between the selected torque wrench
model and "READY".
Whether Automode is ON or OFF, the
actual torque value (based on system
pressure) will appear on the numeric
display. It will remain at "0" until pump
motor is started.
6.5 H "Main" Menu (PSI, BAR or MPa selected)
If Automode is ON, and
(see Screen 8A)
a pressure unit has been selected,
the screen will display "AUTO". Refer
to QRC step #4D.
(See Screen 8B) If Automode is OFF,
the screen will display "READY".
Whether Automode is ON or OFF, the
actual system pressure will appear
on the numeric display. It will remain
at "0" until pump motor is started.
6.5 I "Motor" Menu
This screen allows
(see Screen 9)
the operator to read the number
of hours or on/off cycles the motor
has been operated. Toggle between
hours and cycles by pushing either
the Down or Up Arrow button.
Step forward by pressing the Menu
button. Refer to QRC step #5.
____________________________________________________
__General note for all hour and cycle displays:
HOURS DISPLAYED
- up to 9999.9 the display will show decimal hours.
- between 10,000 - 99,999 whole hours will be
displayed (decimal "." is not displayed).
- over 99,999 hours the meter starts over at 0.0 reading
decimal hours.
CYCLES DISPLAYED
- over 99,999 cycles the meter starts over at 0.
______________________________________________________
Screen 7A
SQD 160 I
0
Ft-lb
Screen 7B
AUTO
0
Ft-lb
Screen 7C
READY
0
Ft-lb
Screen 8A
AUTO
0
PSI
Screen 8B
READY
0
PSI
Screen 9
MOTOR
4.8
HOURS CYCLES
8
6.5 J "Low Volt" Menu
This screen allows the
(see Screen 10)
operator to read the number of hours
the pump has been operated in a low-
voltage condition. Step forward by
pressing the Menu button. Refer to
QRC step #6.
6.5 K "Advance" Menu
This screen allows the
(see Screen 11)
operator to read the total number
of hours that the valve solenoid has
been in the advance position. It also
displays the total number of advance
cycles. Toggle between hours and
cycles by pushing either the Down or
Up Arrow buttons. Step forward by
pressing the Menu button. Refer to
QRC step #7.
6.5 L "Retract" Menu
This screen allows the
(see Screen 12)
operator to read the total number of
hours that the valve solenoid has been
in the retract position. It also displays
the total number of retract cycles.
Toggle between hours and cycles by
pushing either the Down or Up Arrow
buttons. Step forward by pressing the
Menu button. Refer to QRC step #8.
6.5 M "Local" Menu
This screen allows the
(see Screen 13)
operator to toggle the Local mode ON
or OFF (default is OFF). Local mode
allows operation of the pump if the
pendant or pendant cord is damaged.
With Local mode ON, the shroud
buttons replace the pendant buttons
as the method of operating the pump,
and the pendant buttons become deactivated. Toggle Local
mode ON or OFF by pressing the Down or Up Arrow button.
When Local mode is ON, the text "LOCAL" replaces "READY"
on the Normal Operation menu. Save setting and step forward
by pressing the Menu button. Refer to QRC step #9.
6.5 N "Language" Menu
This screen allows the
(see Screen 14)
operator to change the LCD display
language. When a language is shown on
the LCD, press the Down or Up Arrow
buttons to select a diff erent language.
Save setting and step forward by pressing
the Menu button. Refer to QRC step #10.
Screen 10
LOW VOLT
.0
HOURS
Screen 11
ADVANCE
188
HOURS CYCLES
Screen 12
RETRACT
334
HOURS CYCLES
Screen 13
LOCAL
SET
OFF
Screen 14

ENGLISH

SET