Initializing The Modes; Warning/Alarm Indications - Panasonic PV-GS9 Mode D'emploi

: LED Video Light is on. (p. 26)
GAINUP: Gain up Mode (p. 26)
(White): DPOF Setting completed (set to 1 or
more picture) (p. 41)
: [640 x 480] Image size
640
• For images not recorded with this Camcorder, the
size display is determined as follows according to
the number of horizontal pixels.
: 640 or more, less than 800 (The size
640
is not displayed at under 640 pixels.)
: 800 or more, less than 1 024
SVGA
: 1 024 or more, less than 1 280
XGA
: 1 280 or more, less than 1 600
SXGA
: 1 600 or more, less than 2 048
UXGA
: 2 048 or more
QXGA
(Cyan): Photoshot Mode
PICTURE
(Red): While Photoshot recording is
PICTURE
activated
(Green): While the card is being read
PICTURE
No Card (Still Picture Mode)
(Red):
PICTURE
To Change the Counter Display Mode
By changing [C.DISPLAY] on the [DISPLAY]
Sub-Menu, you can change the Counter Display Mode
to Tape Counter Indication [COUNTER] (0:00.00),
Memory Counter Indication [MEMORY] (M0:00.00),
and Time Code Indication [TIMECODE] (0h00m00s00f).
(p. 21) By repeatedly pressing the [DISPLAY] Button
on the Remote Control, you can change the Counter
Display Mode.
To Display Date/Time Indication
To display Date/Time Indication, set the appropriate
Date/Time in [DATE/TIME] on the [DISPLAY]
Sub-Menu. (p. 21)
You can also press the [DATE/TIME] Button of the
Remote Control repeatedly to display or change the
Date/Time Indication.
To Change the Display Mode
By changing [DISPLAY] on the [DISPLAY] Sub-Menu,
you can change the Display Mode to All Function
Display [ALL] and Minimum Display [OFF]. (p. 21)
Progressive Photoshot
You cannot use the Progressive Photoshot Function in
the following cases.
When using Tape Recording Mode
• Digital Effect Modes in [EFFECT1]
• Digital Zoom [D.ZOOM]
• 1/750 s or faster shutter speed
• When brightness is insuffi cient
• When the MagicPix Function is ON
• When the Portrait Mode is used
When using Card Recording Mode
• When brightness is insuffi cient
• When the MagicPix Function is ON
60
Others

Initializing the Modes

You can change the Menu settings back to the
shipping condition.
1 Set [INITIAL] >> [INITIAL SET] >> [YES].
• The initializing takes a little while.
• After the initializing is completed, the [COMPLETED]
Indication appears with beeps.
• Initializing will not erase a clock setting (p. 23) that
has been adjusted.

Warning/Alarm Indications

If any one of the following indications lights up or
fl ashes, please check the condition of the Camcorder.
DEW (DEW DETECTED/EJECT TAPE):
Condensation has occurred. (pp. 66-67)
(CHECK REC TAB):
The accidental erasure prevention slider on the
inserted Cassette is open (that is, set to [SAVE]).
You are attempting Audio dubbing or Digital
dubbing on a Tape while setting the accidental
erasure prevention slider to [SAVE].
(TAPE NOT INSERTED):
No Cassette in inserted. (p. 17)
(LOW BATTERY):
The Battery is low. Recharge it. (p. 16)
:
The built-in battery is low. (p. 23)
(NEED HEAD CLEANING):
The video heads are dirty. (p. 67)
END (TAPE END):
The tape came to an end during recording.
REMOTE (CHECK REMOTE MODE):
Wrong Remote Control Mode has been selected.
(p. 15)
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a tape section
that has been recorded with a different TV system.
UNABLE TO A.DUB
(LP RECORDED):
Because the original recording was done in LP
Mode, audio dubbing cannot be performed.
INCOMPATIBLE TAPE:
This cassette is incompatible.
PUSH THE RESET SWITCH:
Irregular mechanism is detected. Press the
[RESET] Button (p. 70). This may solve the
problem.
CARD FULL:
Card does not have suffi cient memory remaining.
Select Picture Playback Mode and delete
unnecessary fi les.