After Use; Maintenance Schedule; Lubricating The Machine - Nilfisk SC6500 Mode D'emploi

Masquer les pouces Voir aussi pour SC6500:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

A - ENGLISH

AFTER USE

1
When nished scrubbing, press the Scrub Off Switch (E). This will automatically raise, retract and stop all the machine systems (brush, squeegee, vacuum,
solution and detergent (EcoFlex models)). Then drive the machine to a service area for daily maintenance and review of other needed service up keep.
2
To empty the solution tank, remove the Solution Drain Hose (4) from its storage clamp. Direct the hose to a designated "DISPOSAL SITE" and remove the
plug. Rinse the tank with clean water.
3
To empty the recovery tank, pull the Recovery Tank Drain Hose (19) from its storage area. Direct the hose to a designated "DISPOSAL SITE" and remove
the plug (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled ow of waste water). The Recovery Tank Drain Hose can
be squeezed to regulate the ow. Rinse the recovery tank with clean water. Inspect the recovery and vacuum hoses; replace if kinked or damaged.
4
Remove the brushes or pad holders. Rinse the brushes or pads in warm water and hang up to dry.
5
Remove the squeegee, rinse it with warm water and re-install on mount.
6
Remove the hopper on cylindrical systems and clean thoroughly. Remove from either side of the machine by removing the skirt and tilting the hopper up and
away from housing, then pull out.
7
Check the maintenance schedule below and perform any required maintenance before storage.

MAINTENANCE SCHEDULE

Check/Clean the vacuum motor foam lter(s)
Check Foot/ Parking Brake For Wear & Adjustment
Clean Solution Trough on Cylindrical System
* Have Nil sk check the vacuum motor carbon motor brushes once a year or after 300 operating hours. The brush and drive motor carbon brushes check every
500 hours or once a year.
NOTE: Refer to the Service Manual for more detail on maintenance and service repairs.
8
Store the machine indoors in a clean dry place. Keep from freezing. Leave the tanks open to air them out.
9
Turn the Master Key Switch (A) OFF (O) and remove the key.
10
Batteries are the most expensive replacement item on this machine. To protect your investment and to get as many cycles from the batteries as possible,
remember the following:
• Batteries will last longer if kept fully charged.
• Batteries equipped with this machine will not develop a memory.
• Batteries will last longer and will deliver more cycles if they are opportunity charged.
• Battery chargers will not over or undercharge the batteries.
• Batteries will prematurely fail if stored in a discharged state.
• Every day after use, the battery charger must be plugged in and the charger must be allowed to run through a full charging sequence to fully charge the
batteries.
LUBRICATING THE MACHINE – FIGURE 9
Once a month, pump a small amount of grease into each grease tting on the machine until grease seeps out around the bearings.
Grease fi tting locations (or apply grease to) (AA):
Squeegee Caster Wheel Axle and Pivot
Steering Wheel Shaft Universal joint
Steering Chain
Squeegee mount angle adjustment knob threads
Once a month, apply light machine oil or synthetic lubricant spray to lubricate (BB):
Squeegee tool end wheels
Brake Pedal (parking brake) linkage
Side Skirt Height Adjustment Knobs
A - 18
INSTRUCTIONS FOR USE
MAINTENANCE ITEM
Charge Batteries
Check/Clean Tanks & Hoses
Check/Clean/Rotate the Brushes/Pads
Check/Clean the Squeegee
Check/Clean Vacuum Shut-Off Float
Clean Hopper on Cylindrical System
Check Each Battery Cell(s) Water Level
Inspect Scrub Housing Skirts
Inspect and clean Solution Filter
Purge Detergent System (EcoFlex only)
Side Broom Maintenance
Lubrication - Grease Fittings
* Check Carbon Brushes
SC6500 - 56091145
Daily
Weekly
Monthly
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Yearly
X
12/2014

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

56414022564140235641402456414025

Table des Matières