After Use; Maintenance; Maintenance Schedule - Nilfisk SW8000 Mode D'emploi

revised 8/2018

AFTER USE

1 Shake the Hopper Dust Control Filter (LL) and empty the hopper.
2 Check the maintenance schedule and perform all required maintenance before storage.
3 Move the machine to an indoor storage area.
4 Shut down the engine according to the shutdown procedures.
5 Make sure the Ignition Switch (TT) is OFF and the Parking Brake (F) is engaged. NOTE: Press Brake Pedal / Parking Brake (F) and rock your foot forward.
NOTE: If sweeping organic debris, always empty and clean the hopper before storing to prevent odors.
NOTE: It is safe to clean this machine with a pressure washer as long as you do not spray directly at or into electrical components. The machine should always
be allowed to dry completely before each use.
TO SHUT DOWN THE DIESEL & GASOLINE / PETROL ENGINE...
1 Raise the brooms.
2 Place the Engine Speed Switch (GG) in IDLE and let the engine idle for 25 - 30 seconds.
3 Turn the Ignition Key Switch (TT) OFF and remove the key. NOTE: The engine will continue to run for a few seconds after switching the key to off. This is
part of the proper operation of the closed loop electronic control system.
4 Apply the Parking Brake (F). NOTE: Press Brake Pedal / Parking Brake (F) and rock your foot forward.
TO SHUT DOWN THE LPG ENGINE...
1 Raise the brooms.
2 Turn the service valve on LPG Tank (21) OFF.
3 Run the engine until all the LPG is dispelled from the line (the engine will stall).
4 Turn the Ignition Key Switch (TT) OFF and remove the key.
5 Apply the Parking Brake (F). NOTE: Press Brake Pedal / Parking Brake (F) and rock your foot forward.
REPORT ANY DEFECT OR MALFUNCTION NOTED DURING OPERATION TO AUTHORIZED SERVICE OR MAINTENANCE PERSONNEL.

MAINTENANCE

Make sure that the machine is kept in top shape by following the maintenance schedule closely. Repairs, when required, should be performed by your Authorized
Nil¿ sk Service Center, who employs factory trained service personnel and maintains an inventory of Nil¿ sk Original Equipment Replacement Parts and
Accessories.
NOTE: Refer to the Service Manual for more detail on maintenance and service repairs.

MAINTENANCE SCHEDULE

Maintenance intervals given are for average operating conditions. Machines used in severe operational environments may require service more often.
Perform the "After Use" maintenance steps
Check ¿ lter indicator and lights (hyd & air)
Clean the DustGuard system spray nozzles
Clean the DustGuard™ Spray Nozzles (15) and Strainer (30)
* Check / Clean Hopper Dust Control Filter Using Method "A"
* Check / Clean Hopper Dust Control Filter Using Method "B"
* Check / Clean Hopper Dust Control Filter Using Method "C"
*See the Mechanical Repair Service Manual for detailed maintenance information of systems listed. (Sweeping, Hopper, Steering, Dust Control). NOTE: Cleaning
the hopper dust control ¿ lter is not required on models using the maintenance free bag ¿ lter.
4/2015
MAINTENANCE ITEM
Check parking brake
Check engine oil
*Clean main and side broom(s)
Check engine coolant level
Check hydraulic oil level
MAINTENANCE ITEM
*Rotate main broom
*Inspect/adjust brooms
*Inspect broom housing skirts
*Inspect hopper seals
Clean radiator and oil cooler
Perform engine maintenance
*Inspect and grease steering spindle
Change the hydraulic oil ¿ lter
Change reservoir hydraulic oil
Flush the radiator
Engine fuel ¿ lter(s)
PERFORM DAILY
X
X
X
X
X
X
X
X
15 hrs. 30 hrs. 150 hrs. 300 hrs. 1000 hrs.
X
X
X
X
X
X
X
X
X
X
FORM NO. 56091188 - SW8000 - A-13
ENGLISH / A-13
X
X
X
X
X