After Use; Maintenance Schedule - Nilfisk Advance CMAX 28ST Mode D'emploi

WET VACUUMING WET V WET V WET V WET V ACUUMING ACUUMING ACUUMING ACUUMING
Fit the machine with optional attachments for wet vacuuming.
1 1 1 1 1 Disconnect the squeegee hose from the Squeegee (8).
2 2 2 2 2
Attach suitable wet pick-up tools to the hose. (Available from Nilfisk-Advance).
3 3 3 3 3 Turn the Master Key Switch (B)
will run continuously until the button is pressed again to turn it OFF. NOTE:
is not full, the automatic shut-off feature can be disabled, have a qualified service technician refer to the service manual to perform this
function.

AFTER USE

AFTER USE
AFTER USE AFTER USE AFTER USE
1 1 1 1 1
When finished scrubbing, press and hold the Scrub OFF Button (H)
automatically raise, retract and stop all the machine systems (brush, vacuum & solution). Raise the squeegee (17)
to a service area for daily maintenance and review of other needed service up keep.
2 2 2 2 2 Turn the Master Key Switch (B)
3 3 3 3 3 To empty the solution tank, pull the Solution Drain Hose (4)
tank with clean water. Inspect the solution hoses; replace if kinked or damaged.
4 4 4 4 4 To empty the recovery tank, take the Recovery Drain Hose (5)
the plug (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled flow of waste water). Rinse the tank
with clean water. Inspect the recovery and vacuum hoses; replace if kinked or damaged.
5 5 5 5 5 Remove the brushes or pad holders. Rinse the brushes or pads with warm water and hang it up to dry. Allow buffing pads to dry completely
before using again.
6 6 6 6 6 Remove the squeegee, rinse it with warm water and hang it up to dry.
7 7 7 7 7 Check the maintenance schedule below and perform any required maintenance before storage.

MAINTENANCE SCHEDULE

MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE
Check / Clean Tanks & Hoses
Check / Clean the Brushes/Pads
Check / Clean Vacuum Shut-Off Float
Clean Hopper (19)
Check Each Battery Cell(s) Water Level
Inspect Scrub Housing Skirts
Inspect and Clean Solution Filter (18)
Check Hand Brake For Wear & Adjustment (optional)
Clean Solution Trough on Cylindrical System
*Have your Nilfisk-Advance Dealer check the carbon motor brushes once a year or after 300 operating hours.
8 8 8 8 8 Store the machine in a clean, dry place.
48 48 48 48 48 - FORM NO. 56041519 - CMAX
(8). (8). (8). (8).
(B) (B) (B) ON, next press and hold the Vacuum Button (E) (B)
(B) (B) OFF and remove the key. (B)
(B)
(4) off the elbow. Direct the hose to a designated "DISPOSAL SITE". Rinse the (4) (4) (4)
(5) (5)
Maintenance Item Maintenance Item Maintenance Item
Maintenance Item Maintenance Item
Check / Clean the Squeegee
Charge the Batteries
(19) (19) (19) (19) on Cylindrical System
(18) (18)
(18) (18)
Lubricate the Machine
*Service the Vacuum Motor
™ 28ST, 34ST / I-MAX 28C, 32C / BA 750ST, 750C / BA 850ST
(E) (E) until the indicator light turns green. The vacuum motor (E) (E)
NOTE: NOTE: NOTE: NOTE: If the control repeatedly gives a full indication when the tank
(H) (H) (A) (A)
(H) (H) until the display (A) (A) (A) reads "0" and then press again, this will
(5) (5) off its hanger. Direct the hose to a designated "DISPOSAL SITE" and remove
Daily Daily Daily Weekly Weekly Weekly Monthly Monthly Monthly
Daily Daily Weekly Weekly Monthly Monthly
X
X
X
X
X
X
X
X
X
X
X
(17), then drive the machine (17) (17)
(17)
Yearly Yearly Yearly
Yearly Yearly
X
X