Table des Matières
Publicité
DESCRIPTION OF INDICATORS ON THE CONTROL P
DESCRIPTION OF INDICA
DESCRIPTION OF INDICA
DESCRIPTION OF INDICA
DESCRIPTION OF INDICA
In general, the following guidelines apply to the control panel indicators:
A steady red indicator means that the function is inhibited for some reason .
A flashing red indicator means that a fault has occurred in the particular system . An example of this would be an over-current fault.
A yellow indicator means that the particular function has been enabled but is not currently on . For example, if the scrub system is activated and
the Drive Paddle (3)
(3)
(3)
(3) is in neutral, the vacuum and solution indicators will all be yellow indicating that the systems are enabled and ready to turn
(3)
on when the Drive Paddle (3)
(3)
(3)
(3) is moved to forward or reverse.
(3)
A green indicator means that the particular system is on .
A flashing green indicator means that the particular system is in a delayed-off condition . An example of this is when the scrub system is activated
and the Drive Paddle (3)
(3)
(3)
(3)
(3) goes from forward or reverse to neutral. When this happens the vacuum indicator will flash green indicating that the
vacuum is still on but that it will be turning off after the delay period.
Scrub Pressure/Hourmeter Display (A):
Scrub Pressure/Hourmeter Display (A):
Scrub Pressure/Hourmeter Display (A):
Scrub Pressure/Hourmeter Display (A):
Scrub Pressure/Hourmeter Display (A):
•
The scrub pressure/hourmeter display will scroll the hourmeter information only if all of the systems are turned off and the throttle has been
in neutral for at least ten seconds. The hourmeter information will also be displayed immediately once the key switch has been turned on.
•
If any of the systems are turned on or the throttle is in forward or reverse, the display will show the relative scrub pressure value (1-9) or
0 if the scrub system is off. This value is a relative indication of scrubbing effort. It is not an absolute indication of the scrub pressure.
Solution System Indicator (C):
Solution System Indicator (C):
Solution System Indicator (C):
Solution System Indicator (C):
Solution System Indicator (C):
•
This indicator will be green if the solution is on.
•
This indicator will be yellow if the solution is enabled but not turned on.
•
This indicator will be off if the solution is disabled and turned off.
Vacuum System Indicator (F):
Vacuum System Indicator (F):
Vacuum System Indicator (F):
Vacuum System Indicator (F):
Vacuum System Indicator (F):
•
This indicator will be green if the vacuum is on.
•
This indicator will flash green at a slow rate if the ten second delayed turn-off timer is running.
•
This indicator will be yellow if the vacuum is enabled but not turned on.
•
This indicator will flash yellow at a fast rate if there is an overload of the vacuum motor.
•
This indicator will be off if the vacuum is disabled and turned off.
Scrub Off Indicator (I):
Scrub Off Indicator (I):
Scrub Off Indicator (I):
Scrub Off Indicator (I):
Scrub Off Indicator (I):
•
This indicator will be green if the scrub system is ready to be turned on.
•
This indicator will red if for any reason the scrub system cannot be turned on.
•
This indicator will flash red at a fast rate if there is an overload of the brush motors or the brush lift actuator motor.
•
This indicator will be off if the scrub system has been activated.
Recovery Tank FULL Indication:
Recovery Tank FULL Indication:
Recovery Tank FULL Indication:
Recovery Tank FULL Indication:
Recovery Tank FULL Indication:
•
If the recovery tank reaches the full level, the float ball will plug the vacuum inlet which will cause the control system to shut off the scrub,
vacuum, and solution systems. The hour meter/status display (A)
•
Pressing the scrub-off/pressure-decrease, scrub-on/pressure-increase, or vacuum buttons will clear the full indication.
•
The automatic vacuum shutoff feature can be disabled if the vacuum shuts off even when the tank is not full. Refer to the service manual
for information regarding this procedure.
System Overload Indications:
System Overload Indications:
System Overload Indications:
System Overload Indications:
System Overload Indications:
•
If the scrub motors or the scrub deck lift actuator become overloaded, the scrub and solution systems will turn off and the scrub-off/
pressure-decrease indicator will flash red at a fast rate (four times per second).
•
If the vacuum motor becomes overloaded, the scrub, vacuum, and solution systems will turn off and the vacuum indicator will flash yellow
at a fast rate (four times per second).
•
To reset an overload condition, turn the key switch off and then back on.
20 20 20 20 20 - FORM NO. 56041519 - CMAX
TORS ON THE CONTROL PANEL:
TORS ON THE CONTROL P
TORS ON THE CONTROL P
TORS ON THE CONTROL P
(A)
(A)
(A) will scroll the word "FULL" to indicate that the tank is full.
(A)
™
28ST, 34ST / I-MAX 28C, 32C / BA 750ST, 750C / BA 850ST
ANEL:
ANEL:
ANEL:
ANEL:
Publicité
Table des Matières
