Ordering Spare Parts; Software Update; Transport - EINHELL FREELEXO BT Instructions D'origine

with new ones. Always replace all three bla-
des (10) as a set.
3. Then retighten the fastening screw. Check
that the new blades (10) are able to rotate
freely.
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which may have accumulated. At the start of
each season, ensure that you check the condition
of the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.

7.2.2 Software update

If you want to update the software, copy the new
software to an empty USB stick (format the USB
stick fi rst if necessary). Make sure that the rechar-
geable battery is fully charged before you carry
out the following steps.
1. Place the robot lawn mower in the area to be
mowed. The robot lawn mower must not be
in the charging station during the software
update.
2. Connect a USB stick to the USB connection
as shown in the illustration (Fig. 11)..
3. Switch on the main switch (7) (ON).
4. Press the POWER button (60) and the "OK"
button (61) at the same time. Keep the but-
tons pressed for 5 seconds. All the LEDs (50,
51, 52, 53) on the control panel will now have
come on (2).
5. Press the "4" button / lock button (65) to start
the update. The time LEDs (50) show the cur-
rent progress. When all 5 time LEDs (50) are
lit together, this means that the process has
been completed.
6. After a few seconds the time LEDs (50) will
go out again and the robot lawn mower will
switch to normal operating mode with just one
time LED (50) on.
7. Pull out the USB stick.
7.2.3 Repairing the perimeter wire
If the perimeter wire (18) gets severed at any
point, use the supplied cable connectors (16) to
repair it. To do so, insert both ends of the severed
perimeter wire (18) into the cable connector (16)
and squeeze it together with the help of a pair of
pliers. Connect the power plug to the socket out-
let. Then check whether it is working properly by
checking the LED indicator (21) on the charging
station (19).
Anl_FREELEXO_BT_SPK13.indb 42 Anl_FREELEXO_BT_SPK13.indb 42
GB

7.3 Ordering spare parts

Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Replacement blades Art. No.: 34.140.20
8. Storage
Fully charge up the rechargeable battery (A) be-
fore putting it into storage over winter and switch
off the robot lawn mower at the main switch (7)
(OFF). Take the rechargeable battery (A) out of
the equipment. Disconnect the power supply
unit (13) from the power supply and the charging
station (19).
The perimeter wire (18) can be left outdoors over
winter. However, make sure that the connections
are protected against corrosion. To do so, discon-
nect the connections of the perimeter wire (18)
from the charging station (19).
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30°C. Store the equipment
in its original packaging.

9. Transport

•
Switch off the equipment at the main switch
(7) (OFF) (Fig. 8)..
•
Fit the shipping protectors, if any.
•
Protect the machine from damage and the
strong vibrations that can occur particularly
when transporting in vehicles.
•
Secure the machine against slipping and tip-
ping over.
•
Carry the robot lawn mower by the carry-
handle (6) with the blade plate (11) facing
away from your body.
- 42 -
22.09.2021 10:12:12 22.09.2021 10:12:12