Kärcher TB 36 Notice Originale page 34

Safety instructions
In the event of danger for persons, property
and animals, the plant must be switched off
immediately by pressing the emergency-
stop button. It is found
at the wash card/code reader
–
at the control panel
–
at the entrance to the wash hall, íf an
–
operating point or wash card/code
reader is located there.
Warning!
Risk of damage to vehicle which is to be
cleaned. If the wash plant develops a fault
once the detergent has been applied, it
must be switched off and the detergent re-
moved by spraying the vehicle thoroughly
with water to prevent the paintwork being
damaged through an extended period of
exposure to the detergent.
Note
In the case of self-operating plants, a spe-
cialist familiar with the plant must be con-
tactable who can carry out measures, or
have them done, in order to avoid possible
dangers.
Switching on after emergency-stop
 Release emergency-stop button by
pulling it.
 Set automatic/manual switch at the
feeder to automatic.
 Press button "Reset" Setting for 2 sec-
onds.
The system will automatically drive into the
basic position.
Note: If a vehicle is present in the washing
system, the system might have to be driven
into the basic positions using the manual
function in some cases.
In the basic position, the key "Start/Stop"
will be illuminated.
The system is once again ready-to-use.
Start up
 Stop valve opens for water and com-
pressed air.
 Set the main switch on the feeder dis-
tributor to "1".
 Preselect the speed, control panel and
operating mode at the switches on the
feed distributor.
 Set automatic/manual switch to auto-
matic.
 Press button "Reset" Setting for 2 sec-
onds.
In the basic position, the key "Start/Stop"
will be illuminated.
The plant is again ready for operation and
the the vehicle being washed can be driven
in.
34
Operation
Preparing the vehicle
Warning
When using Carlite brushes, the vehicle
must be manually cleaned beforehand, if
the appliance is not equipped with an up-
grade kit high pressure!
Warning
In order to avoid damage to the vehicle, the
following precautionary measures have to
taken on the vehicle before starting the
wash plant:
 Close windows, doors and roof open-
ings.
 Push in antennas, fold over in direction
of rear or dismantle.
 Fold in large or wide overhanging mir-
rors.
 Check vehicle for loose vehicle parts
and dismantle them, e.g.:
trim strips,
–
spoilers,
–
bumpers,
–
door handles,
–
exhaust pipes,
–
wind-breakers,
–
tilt ropes,
–
rubber gaskets,
–
sunshades attached to the outside of
–
the vehicle,
luggage racks,
–
ski box.
–
Driving in the vehicle
Vehicle positioning traffic light (option)
The positioning ramp supports the custom-
er in correctly positioning the vehicle.
1 Drive forward
2 Stop, position is correct
3 Reverse drive
 Position the vehicle straight and in the
middle between the drive-rails.
After the positioning
 Switch off engine.
 Put gear in. Choose position "P2" with
automatic gearbox.
 Pull up handbrake.
 Check whether the directions in the
"Preparing the vehicle" section have
been followed.
 Leave vehicle (all occupants) and start
wash programme.
8
-
EN
Note: Do not leave the vehicle during
short wash, counter wash, drive
through wash and automatic start.
Start program
at the wash card/code reader (option)
The operation with a wash card/code read-
er is described in the separate operating in-
structions for the wash card/code reader.
With control panel adv. (option)
 Turn the programme selection switch to
the desired cleaning program.
 Press the key for the desired additional
programme.
 Press the key for the desired pro-
gramme option.
 Press the "Start/Stop" key.
The washing process is started
With basic control panel (option)
 Press one or several buttons to start the
desired wash programme. (see follow-
ing table
1
Programme 1 X
Programme 2
Programme 3 X
Programme 4
Programme 5 X
Programme 6
Programme 7 X
 Press the "Start/Stop" key.
The washing process is started
Interrupt programme
 Press the "Start/Stop" key.
The washing programme is interrupted.
 Press the "Start/Stop" key again.
The washing programme is continued.
2 4
X
X
X
X
X X
X X