Lighting The Heater For The First Time; Extra Protection; Disposal; Guarantee - Dru SAXO SL 70 Instructions D'installation Et Mode D'emploi

GENERAL NOTES

Lighting the heater for the first time

There can be an unpleasant smell when you light the heater
for the first time. This is caused by the varnish evaporating
and will disappear after a few hours. We therefore advise
you, on initial use, to heat the appliance at the highest
setting while ventilating the room it is installed in well.

Extra protection

This heater meets the normal safety standards regarding
surface temperatures, but physical contact with heated
surfaces should be avoided where possible. An additional
guard is recommended to protect young children and
elderly, infirmed or handicapped people. For safety
reasons a guard should be placed in front of the fire at all
times.
OBSERVED PROBLEM:
A. No Transmission:
(motor does not turn)
WARNING:
Do not create an electrical short between the
batteries/battery box and metal parts of the
appliance. It will damage the remote
(see figure 2).
B. No Ignition:
WARNING:
Do not create an electrical short between the
batteries/battery box and metal parts of the
appliance. It will damage the remote
(see figure 2).
fig. 2
C. No Tone:
D. One 5 second continuous tone
(7 short beeps might be heard prior to the
5 second tone):

Disposal

When replacing or otherwise removing the appliance, it
should be disposed of in compliance with current regulations.
Shut off the connecting tap with coupling before
commencing disassembly. Undo the coupling between the
connecting tap and the appliance. The whole appliance can
now be disassembled and removed.

Guarantee

The warranty for your DRU appliance will be provided by
your supplier. In case of malfunctions, you should always
contact him. You supplier will contact DRU if he feels this
is necessary. The factory warranty for your appliance is
valid for 2 years after date of purchase.
POSSIBLE CAUSE:
1. Receiver must learn new code.
2. Dead batteries.
3. Receiver damaged.
4. Transmitter damaged.
5. Motor cable at valve broken.
6. Bent pins on 8 wire connector.
7. If the receiver is surrounded by metal,
it can reduce the transmission range.
1. ON/OFF switch in OFF position. Manual
override knob in MAN position.
WARNING:
Make sure that the antenna is not too close to
the ignition cable and ignition coil (beneath the
cover). It will damage the receiver (see figure 3).
correct position
2.
1.
of antenna
1. antenna ignition cable
2. coil (inside)
3. antenna
fig. 3
1. Receiver damaged.
2. 60-second delay before the full restart is
not yet finished.
1. ON/OFF switch is in OFF position.
2. Loose wire.
3. Receiver damaged.
4. Bent pins on 8 wire connector.
5. Valve damaged.
6. Thermocouple 2 still too hot.
35
TROUBLESHOOTING
REMEDY:
1. Press and hold the receiver's reset button
until you hear 2 acoustic signals. After the
second longer acoustic signal release the
reset button and within the subsequent
20 seconds, press the
handset, until you hear an additional long
acoustic signal confirming the new code is
set (see figure 1).
2. Replace the batteries.
3. Replace receiver and reprogram code
(remedy 1).
4. Replace the transmitter and reprogram the
code (remedy 1).
5. Replace motor cable at valve.
6. Straighten pins on 8 wire connector.
7. Change the position of the antenna.
fig. 1. Receiver with Reset button
1. Turn ON/OFF switch to ON position and
the knob for the manual override to the
ON position (see figure 4).
3.
fig. 4
1. Replace receiver and reprogram code
( remedy 1).
2. Wait until the delay time has passed.
1. Push switch to ON position.
2. Secure wire.
3. Replace receiver and reprogram code
(remedy 1).
4. Straighten pins on 8 wire connector.
5. Replace valve.
6. Wait until the thermocouple has cooled
down sufficiently"
on the remote
Saxo SL