Maintenance And Servicing; Maintenance And Cleaning; Accessories - Bosch GTS 635-216 Professional Notice Originale

42 | English
Checking
The marking in the magnifying glass (54) must be in line with
the 0 mm mark on the scale (1).
Setting
– Loosen the screw (65) using a cross-headed screwdriver
and align the marking along the 0 mm mark.
Adjusting the level of the table insert (see figure N)
Checking
The front side of the table insert (23) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Setting
– Use the tip of the ring spanner (9) to set the adjusting
screws (66) to the correct level.
Storage and transport (see figures O1 − O2)
Storing tool elements
You can attach certain tool elements to the power tool to
store them.
– Detach the additional parallel guide (40) from the parallel
guide (5).
– Place all loose components of the tool in their storage
compartments on the housing (see the following table).
Tool element Storage compartment
Parallel guide (5) Turn around, suspend from below
in the guide rails and secure the
clamping handle (38)
Push stick (12) Place in the storage compartment
(67)
Protective cover (3) Place in the recess on the bracket
(11) and secure using the clamping
lever (36)
Hex key (10) Place in the storage compartment
(68)
Ring spanner (9) Place in the storage compartment
(69)
Angle guide (2) Place in the storage compartment
(7)
Additional parallel Push into the groove at the back of
guide (40) the parallel guide (5) and tighten
using the wing bolts
Transporting the power tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position (see
"Transport position", page 38).
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in a closed con-
tainer.
– Slide the saw table expansion (6) in fully and push the
clamping handle (13) down to secure it in place.
– Wrap the power cable around the cable holder (26).
1 609 92A 4PA | (01.03.2019)
– Use the carrying handles (27) to lift or transport the tool.
Only use the transport devices to transport the power
u
tool and never the protective devices.

Maintenance and servicing

Maintenance and cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Cleaning
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Noise reduction measures
Measures implemented by the manufacturer:
– Soft start
– Provided with a saw blade specially developed for noise
reduction
Measures implemented by the operator:
– Low-vibration mounting on a stable work surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of the saw blade and power tool

Accessories

Angle guide
Push stick
Protective cover
Parallel guide
GTA 560 saw stand
Optiline Wood for the following models:
3 601 M42 000/... 030/... 070
216 x 30 mm saw blade, 22 teeth
216 x 30 mm saw blade, 34 teeth
216 x 30 mm saw blade, 54 teeth
Multi Material for the following models:
3 601 M42 040
216 x 30 mm saw blade, 22 teeth
216 x 25.4 mm with reducing ring
Expert Wood for the following models:
3 601 M42 0B0
216 x 25.4 mm saw blade, 60 teeth
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
Article number
1 609 B04 510
1 609 B06 410
1 609 B04 542
1 609 B04 590
3 601 M22 700
2 608 838 410
2 608 838 409
2 608 838 411
2 608 644 569
2 608 642 995
Bosch Power Tools