Additional Safety Warnings - Bosch GTS 635-216 Professional Notice Originale

Locate the table saw in a well-lit and level area where
u
you can maintain good footing and balance. It should
be installed in an area that provides enough room to
easily handle the size of your workpiece. Cramped,
dark areas, and uneven slippery floors invite accidents.
Frequently clean and remove sawdust from under the
u
saw table and/or the dust collection device. Accumu-
lated sawdust is combustible and may self-ignite.
The table saw must be secured. A table saw that is not
u
properly secured may move or tip over.
Remove tools, wood scraps, etc. from the table before
u
the table saw is turned on. Distraction or a potential jam
can be dangerous.
Always use saw blades with correct size and shape
u
(diamond versus round) of arbour holes. Saw blades
that do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
Never use damaged or incorrect saw blade mounting
u
means such as flanges, saw blade washers, bolts or
nuts. These mounting means were specially designed for
your saw, for safe operation and optimum performance.
Never stand on the table saw, do not use it as a step-
u
ping stool. Serious injury could occur if the tool is tipped
or if the cutting tool is accidentally contacted.
Make sure that the saw blade is installed to rotate in
u
the proper direction. Do not use grinding wheels, wire
brushes, or abrasive wheels on a table saw. Improper
saw blade installation or use of accessories not recom-
mended may cause serious injury.

Additional safety warnings

When mounting the saw blade, wear protective
u
gloves. This poses a risk of injury.
Do not use HSS saw blades. Such saw blades can easily
u
break.
Never use the tool without the table insert. Replace
u
table insert if defective. Without flawless table inserts,
injuries are possible from the saw blade.
Keep your work area clean. Material mixtures are partic-
u
ularly hazardous. Light metal dust may catch fire or ex-
plode.
Choose the saw blade suited to the material you want
u
to work on.
Only use saw blades that match the specifications
u
given in this operating manual and that are tested and
marked in accordance with EN 847-1
Only use saw blades that are recommended by the
u
power tool manufacturer and are suitable for using on
the material you want to saw.
Only advance the workpiece towards the saw blade
u
when it is running. Otherwise there is a risk of kickback
occurring if the saw blade catches in the workpiece.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
Bosch Power Tools
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.
Symbols and their meaning
Keep hands away from the cutting area
while the power tool is running. Con-
tact with the saw blade can lead to injur-
ies.
Wear a dust mask.
Wear hearing protection. Exposure to
noise can cause hearing loss.
Wear safety goggles.
3 601 M42 000
3 601 M42 030
3 601 M42 070
3 601 M42 040
3 601 M42 0B0
Ø 25,4 mm
Ø 216 mm
Take note of the dimensions of the saw blade. The hole dia-
meter must fit the tool spindle without play. If it is neces-
sary to use reducers, ensure that the dimensions of the re-
ducer are suitable for the base blade thickness and the saw
blade hole diameter, as well as the tool spindle diameter.
Wherever possible, use the reducers provided with the saw
blade.
The saw blade diameter must match the information spe-
cified on the symbol.
English | 33
1 609 92A 4PA | (01.03.2019)